Filename: SMT_X10_222.bin version: 2.22 Date: 11-03-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: New Feature Description: Support new NVMe Drive: Samsung PM953 Infected motherboard: All motherboards support NVMe Affected functions: Validation : 1. PM953 does not have VPD. It will only show "Status" and "Temperature" 2. There are only two columns, if the drive is Samsung PM953. 2. Category: New Feature Description: [66664] Some fixed items are incorrect in release note Infected motherboard: All Affected functions: Validation : 1. Check releate note 3. Category: fix Description: [66664] [LCMC FW1.10] Node Configuration Info Still Preserved After Running AC ONOFF Test Infected motherboard: X10DRT-P, X10DRFR,X10DRFF Affected functions: Validation : 1. Do ac on/off testing on all nodes 2. Check the informtion on "Board Part Number" and "Board Serial Number", it should be preserved all the times when status is "Present" 4. Category: Fix Description: Syslog Setting problem. it cannot connect to syslogd server. Infected motherboard: All Affected functions: Validation : 1. Enable syslog option. Setting syslogd server ip address and port (default 514) 2. Install syslogd server application. (Such as Free SysLog forwarder) https://www.manageengine.com/free-syslog-forwarder-tool/free-syslog-forwarder-index.html 3. Setup bmc ip address on application 4. Trigger eventlog such as pull out one existed fan then check log on application 5. Category: fix Description: [66740] No processor automatically throttled event Infected motherboard: X10SLX Affected functions: Validation : 1. Heat CPU temperature 2. Check asserted event log 3. Cool down CPU temperature 4. Check de-asserted event log 6. Category: Fix Description: [66431] BMC sensor reading(HDD Status) don't change when disk detect failed status Infected motherboard: Affected functions: Validation : 1. Check if "HDD Status" shows correct status when it happens Drive Fault error. 7. Category: Fix Description: [66693] smcipmitool ver detection error Infected motherboard: X10QBI Affected functions: Validation : 1. Key in smcipmitool nm command continously 2. Check node manger version and Firmware version. It should be normal 8. Category: Workaround Description: [66231] [2.19 IPMI ECO] Several "C: Boot Completed - Assertion - Assertion" events are recorded in IPMI event log during RHEL 7.1 OS installation Infected motherboard: X10DRG-O Affected functions: Validation : 1. Install RHEL 7.1 OS installation. 2. Check if unwanted event log should not happen. 9. Category: fix Description: KCS failures in IPMI communication between BMC and host after updating IPMI fw from 1.8x to 2.17. Infected motherboard: X10DRW-i Affected functions: Validation : 1. Install at least one recognizable PCIE device on the riser card, such as 10G. 2. Boot up host and see if KCS communication can get stuck. ------------------------------------------------------------------------------ Filename: SMT_X10_221.bin version: 2.21 Date: 10-23-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Workaround Description: X10QBi would hang at post code: 0x4F Infected motherboard: X10QBi Affected functions: Validation : 1. Run the system on/off test. 2. Check it would stop or not. 2. Category: Enhanecement Description: Support Mutlinode function Infected motherboard: X10DRFF Affected functions: Validation : 1. Check multinode web page and related functions 3. Category: Enhanecement Description: Default fan mode is optimal mode by SDM_FSC_Modes (10212015).pdf Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Do factory default action 2. Check fan mode 4. Category: Fix Description: [66411] [BDW-EP] SUM test fail Infected motherboard: All X10 motherboards. Affected functions: Validation : 1. Run SUM TC212/410 5. Category: Fix Description: [66043] No "Processor Automatically Throttled" event. Infected motherboard: X10SLA Affected functions: Validation : 1. Try heat the CPU temperature 2. Check the asserted event log 3. Cool down the CPU temperatue 4. Check the deasserted event log ---------------------------------------------------------------------------------------------------------------- Filename: SMT_X10_220.bin version: 2.20 Date: 10-21-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [64802] Hitachi HUSPR3232ADP301 4.0TB NVMe missing VPD information on IPMI WebGUI. Infected motherboard: All motherboards support Hitachi NVMe Drive Affected functions: Validation : 1. Check the Hitachi Drive slot in NVMe SSD page. 2. Category: Fix Description: Redirect IPMI WEB to the login page after executing factory default. Infected motherboard: All X10 motherboards. Affected functions: Validation : 1. Try factory default and then wait for FW reboot. 3. Category: Fix Description: [66367] IPMI Eject and Insert. Infected motherboard: Motherboards support NVMe Drive Affected functions: Validation : 1. Check the Eject function in NVMe SSD page. 2. Check the Insert function in NVMe SSD page. ---------------------------------------------------------------------------------------------------------------- Filename: SMT_X10_219.bin version: 2.19 Date: 10-05-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 ********************************* X10QBL, X10QBI, X10DRG-O, X10SRG Release Only********************************** 1. Category: New Feature Description: Support 24 NVME solution. Infected motherboard: 24 NVME motherboards. Affected functions: Validation : 1. Check the NVME SSD pagee in WebGui. 2. Category: New Feature Description: Support Hitachi, Samsung PM1725. Infected motherboard: NVME motherboards which support HGTC and Samsung PM1725 Drive. Affected functions: Validation : 1. Check the NVME SSD pagee in WebGui. 3. Category: Fix Description: [65692][65895] Remote windows(Java iKVM Viewer) show incorrect IP Address. Infected motherboard: All X10 Affected functions: Validation : 1. Open iKVM viewer and check displayed IP. 4. Category: Fix Description: [65706] [ECO] System fan C and fan D are out of control with fan mode change Infected motherboard: X10SRG-F Affected functions: Validation : 1. Set full speed mode 2. Check FanC & FanD rpm rise 5. Category: Fix Description: [64802] Hitachi HUSPR3232ADP301 4.0TB NVMe missing VPD information on IPMI WebGUI Infected motherboard: All motherboards which support HGST NVMe drives Affected functions: Validation : 1. Use Hitachi drive 2. Check VPD information 6. Category: Fix Description: [65775] [ECO SMT_X10_218] NO AOC Temp reading when JI2C is enabled Hardware Infected motherboard: X10QBL Affected functions: Validation : 1. Plug in AOC-S40G-i2Q or AOC-STG-I2T 2. Power on or reset the sytem and wait until bios post stage is finished 3. Check AOC 10G/40G senosr appeared on IPMI web gui 7. Category: Fix Description: [65200] Random "Power Supply Input Lost or Out of Range - Assertion / De-Assertion" events were recorded in IPMI SEL Infected motherboard: X10DRG-O Affected functions: Validation : 1. Do bios update action by IPMI web gui 2. Power on the system 3. Check the event log webu gui --------------------------------------------------------------------------------------------------------- Filename: SMT_X10_218.bin version: 2.18 Date: 09-xx-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [65137] [BIOS ECO 1.0a] BIOS Resilience mode to not support IPMI recovery mode. Infected motherboard: X10SRD Affected functions: Validation : 1. Check the function of BIOS Resilience in WebGui. 2. Category: Fix Description: [64885] [IPMI 3.12]10G 40G have no sensor reading. Infected motherboard: X10DRI-P X10DRI-T Affected functions: Validation : 1. Please use 8/31 or above BIOS. 2. Insert the 10G/40G AOC. 3. Power on the system. 4. Check the sensor list. 3. Category: Fix Description: [65219] [IPMI 2.17 ECO] "Power Supply Input Lost or Out of Range - Assertion" after AC power cycle. Infected motherboard: X10DRFF Affected functions: Validation : 1. AC power cycle the SUT. 2. Check the event log. 4. Category: Fix Description: [65107] [Redfish] BIOS Update function descripe show "Undifined" when IPMI web language set to "Chinese" Infected motherboard: All Affected functions: Validation : 1. De-activate the key. 2. Check the BIOS update page. 5. Category: New feature Description: Support 1U Twin Pro. Infected motherboard: X10DRT-P Affected functions: Validation : 1. Support 1U Twin Pro backplane. 2. Change the sensor name FAN3->MB_FAN3, FAN4->MB_FAN4. 3. Add new sensors: FAN1, FAN2, FAN3 ------------------------------------------------------------------------------------ Filename: SMT_X10_217.bin version: 2.17 Date: 08-31-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [64832] Missing MB_10G Temp in IPMI Web GUI with REDFISH 3.12. Infected motherboard: X10DRU-i+, X10DRU-X(LL) Affected functions: Validation : 1. After updating FW, power cycle the SUT. 2. Check the MB_10G Temp1 and Temp2 value. 2. Category: Fix Description: [64690] AOC Temp is misbehave when 10G & 40G populate on certain slots order. Infected motherboard: All support RSC-R2UW-2E8E16 motherboards Affected functions: Validation : 1. Put only two AOC cards onto the Riser Card. 2. Check the AOC Temp values. 3. Remove the AC power. 4. Swap the AOC cards. (Ex: 1,2 -> 2,3) 5. Recover the AC power, check the AOC Temp values. --------------------------------------------------------------------------------------- Filename: SMT_X10_216.bin version: 2.16 Date: 08-21-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: New feature. Description: AOC-URN2-i4GXS support Infected motherboard: X10 motherboards which can support this riser card Affected functions: Validation : 1. Check 10G senosr (no.2) on IPMI web gui 2. Heat 10G sensor if the fan speed increase 2. Category: Enhanecement Description: Thermal guide 4.05 is supported (SIM_TDG REV. 4.05 08072015) Infected motherboard: X10 motherboards Affected functions: Validation : 1. Check fan curve 3. Category: Fix Description: Remove 12V protection support due to requirement change. Infected motherboard: X10DRFF, X10DRT-L Affected functions: Validation : 1. Check for 12V protection event log after AC cycle test. 4. Category: Fix Description: [64462] System lost all sensor readings while doing system on-off test. Infected motherboard: X10QBI Affected functions: Validation : 1. Please also use the latest BIOS (Not release yet, version > X10QBI15.812). 2. Power on the system and wait it go into OS. 3. Check the sensor page. ----------------------------------------------------------------------------------------------- Filename: SMT_X10_215.bin version: 2.15 Date: 08-03-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: New feature. Description: [64190 ] No CPU thermal trip event log [64183] Thermal Trip Event Log Missing after thermal trip X10DRU-X [64072] No Thermal trip event log. Infected motherboard: X10DRW-I, X10DRW-N, X10DRU-X, X10DRU-XLL, X10DRX Affected functions: Validation : 1. Update the latest CPLD FW. 2. Trigger the thermal trip. 3. Check the event log 2. Category: Fix Description: [62019] AOC Temp is misbehave when both 10G & 40G Lan Card populate on the MB. [63344] IPMI 10G 40G AOC reading misbehaving. [63346] IPMI The temperature reading of 40G and 10G can't be display correctly at the same time. Infected motherboard: X10SRW, X10DDW-IN, X10DDW-I Affected functions: Validation : 1. Power off the system. Update the IPMI FW. (Do not preserve the SDR.) 2. Put 10G and 40G LAN card at the same time. 3. Power on the system. Wait the IPMI recreate the SDR. 4. Check the sensor list. 3. Category: New feature. Description: [64058] No CPLD version shows on IPMI Web. Infected motherboard: X10DRD Affected functions: Validation : 1. Update the latest CPLD FW. 2. Check IPMI web page. 4. Category: New feature. Description: [64001] GPU sensor reading not shown in IPMI Web GUI Infected motherboard: X10DRH-CLN4 Affected functions: Validation : 1. Plug GPU on slot 1 or slot 4. 2. Check IPMI web page if any GPU sensor apears. 5. Category: Fix Description: [64018] [2.13 IPMI ECO]BMC alerts subject MB name inconsistent. Infected motherboard: X10DRD-INT Affected functions: Validation : 1. Make the sender's Address not admit the null string. 2. User needs to fill its Email address. 6. Category: Fix Description: [63003] Received "Processor Automatically Throttled - Assertion" message in IPMI event log after system was powered on Infected motherboard: X10QRH+ Affected functions: Validation : 1. Plug in two power supplies. 2. AC off one power supply 3. Check if it should not have any Throttled event log occured ----------------------------------------------------------------------------------------------- Filename: SMT_X10_214.bin version: 2.14 Date: 07-17-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [62940] The thresholds of Vdimm sensors are incorrect. Infected motherboard: X10QBL with DDR4 Affected functions: Validation : 1. After updating the FW, please power cycle the system. 2. BIOS would tell IPMI which DIMM is used and adjust the threshold values. 3. Check the sensor reading page. 2. Category: Fix Description: [61775] NO Scroll bar @ "Sensor Reading"page under IPMNIWeb GUI ON MacOS / Safari Browser Infected motherboard: All X10 Affected functions: Validation : 1. Use Safari to login to IPMI web gui. 2. Go to "Server Health" -> "Sensor Readings", must be able to scroll down to the end of the sensor list. 3. Category: Fix Description: [63103] IPMI WebGUI Showing 4 DIMM sensor readings when only plug in 2 DIMM on MB Infected motherboard: X10DRD-L Affected functions: Validation : 1. Please check IPMI sensor reading web page 4. Category: Fix Description: [63524] [MB v1.01B] IPMI Watchdog function fails Infected motherboard: X10QBI Affected functions: Validation : 1. Use Cmd:0x30 Subcmd:0x97 to set watchdog timer. 2. Wait about 30 seconds. 3. Use Cmd:0x30 Subcmd:0x98 to reset watchdog timer. 4. Wait the timeout time and check the action. 5. Category: Fix Description: The thresholds of Vdimm sensors are incorrect. Infected motherboard: X10SDV Affected functions: Validation : 1. Check the sensor reading page. 6. Category: Enhancement Description: Enable the system event log by default Enable web session timeout default is 30 minutes Infected motherboard: All Affected functions: Validation : 1. Execute 0x30 0x42 command after new IPMI FW is updated 2. Check if system event log default setting is enable 3. Login the web page, wait if logout action is executed after 30 minutes ---------------------------------------------------------------------------------- Filename: SMT_X10_213.bin version: 2.13 Date: 06-26-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [62299] [IPMI] Active Directory Function Under IPMI will not work after setting the default timeout to 0. Infected motherboard: All motherboards Affected functions: Validation : 1. Set the Active Directory Timeout to 0. 2. It should pop out the alert to describe the correct range. 2. Category: Enhancement Description: Removing special character set restriction Infected motherboard: All Affected functions: All Validation : Could use special character in add user and modify user. 3. Category: New Feature Description: LSI 3108 management Infected motherboard: All motherboards which support LSI 3108 monitoring Affected functions: 1. Activate OOB license (have a independent page: "Miscellaneous>Activate License") Validation : 1. MUST enable OOB license 2. Click "Storage Monitoring" page and start to manage RAID * RAID 0, 1, 5, 6, 10, 50 and 60 supported * Add/Delete VD * Start/Stop to locate LED * Get 3108 controller information * Import/Delete foreign configuration * Display progress/remaining time or elapsed time when RAID is rebuilding 3. Suggest to upgrade LSI firmware to MR6.7_GCA_051215 4. Category: Fix Description: [62020 ] No CPLD version shows on IPMI Web Infected motherboard: X10SRW-F Affected functions: Validation : 1. Check if CPLD version show on IPMI web page 5. Category: Fix Description: [61534] [NVMe] IPMI Eject buttom not responding Infected motherboard: All motherboards with NVMe web page Affected functions: Validation : 1. Try to press "Locate" and "Stop Locate" button back and forth 2. Examine If NVMe web page work properly ---------------------------------------------------------------------------------------- Filename: SMT_X10_212.bin version: 2.12 Date: 06-12-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [62361] No Thermal trip logs [62221] No "Thermal Trip" message in IPMI Event Log Infected motherboard: X10DRG-Q, X10SRH-CF Affected functions: Validation : 1. Heat CPU to let system shutdown 2. Check thermal trip event log 2. Category: New Motherboard Description: Support new motherboard X10DRH_LN4 Infected motherboard: X10DRH_LN4 Affected functions: Validation : 3. Category: Fix Description: [62231] SUM Test Case 313 failed under IPMI 2.10 and BIOS 520 [61991] Sum Test Case # 313 Failed Infected motherboard: X10 motherboards Affected functions: Validation : 1. Activate OOB product key 2. Run #313 test case. --------------------------------------------------------------------------------------------- Filename: SMT_X10_211.bin version: 2.11 Date: 06-05-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [61904] FANs 5,6,7,8 do not spin at full speed when Fan mode is set to Full. Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run system. 2. Set different fan modes and then check sensor reading pages for their fan speeds. 2. Category: Fix Description: Fixed the lock for Fru #1 not correctly locked at first time power on and after factory restore. Infected motherboard: All X10 Affected functions: Validation : 1. Do factory restore. 2. Write to Fru #1 and check if the write fails. 3. Category: Fix Description: SMTP Password can accept # and % chacters Infected motherboard: All X10 Affected functions: Validation : 1. Key in # or $ in SMTP password input text on IPMI SMTP Setting web gui 2. This action is prohibited and will see alerts dialog comes out 4. Category: Fix Description: [62269] For samsung nvme IPMI page web-gui shows Unknown for Port 1 speed and Width Infected motherboard: All motherboards support samsung nvme Affected functions: Validation : 1. Check the NVME page. 2. Change the Uknown to N/A. 5. Category: Fix Description: [61782] Vbat voltage in IPMI failed IPMI Infected motherboard: X10DRH-CLN4 Affected functions: Validation : 1. Check VBAT sensor values 6. Category: Fix Description: [62013] X10SRW-F R1.02B sample run report Infected motherboard: X10SRW-F R1.02B Affected functions: Validation : 1. Check CPU VRM sensor if exists 7. Category: Fix Description: [62019] AOC Temp is misbehave when both 10G & 40G Lan card populate on the MB Infected motherboard: X10SRW-F Affected functions: Validation : 1. Install one card on RSC-R1UW-2E16 and another card on RSC-R1UW-E8R. 2. Check 10G sensor and 40G sensor work properly 8. Category: Fix Description: [62221] NO "Thermal Trip" message in IPMI Event Log Infected motherboard: X10SRH-F Affected functions: Validation : 1. This feature need to update the latest CPLD FW. Wait HW release it. 2. Make CPU hot enough to trigger the Thermal trip. 3. Check the SEL. --------------------------------------------------------------------------------------------- Filename: SMT_X10_210.bin version: 2.10 Date: 05-15-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [61383] No sensor readings except for power supply status readings are shown in IPMI Sensor reading page for X10DRG-OT+ (10G SKU) Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run different SKU system. 2. Check their sensor reading pages. 3. 10G SKU system get one more 10G LAN temp than 1G SKU system. 2. Category: Fix Description: [61079] The fan sensor names don't match the silkscreen Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run the system. 2. Check sensor reading page. 3. Category: Fix Description: [61435] Vmem_VRM Temp is shown as Not Present! in IPMI Sensor Readings Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run the system. 2. Check sensor reading page. 4. Category: Fix Description: System will show "The IPMI Configuration file is damage" message when enter IPMI Configuration page. Infected motherboard: All X10 Affected functions: IPMI Configuration save and reload. Validation : 1. Close browser and open a new browser session. 2. Go to IPMI Configuration web page, save the configuration to local. 3. Reload using the configuration that was just saved in #1. 4. After BMC reset completes, go to IPMI Configuration web page again, and there should not be any error message. 5. Category: Fix Description: [61379 ] No GPU/Xeon Phi Temperature Sensor Reading on Rev:1.01 ADP-S3108H-H8iRP Infected motherboard: X10DRT-P Affected functions: Validation : 1. Install GPU and use latest Bios and IPMI FW 2. Check if GPU sensor exists --------------------------------------------------------------------------------------------- Filename: SMT_X10_195.bin version: 1.95 Date: 04-24-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [60981] there are false messages about "CPU3 Temp Thermal Trip Assertion" Infected motherboard: X10QBi Affected functions: Validation : 1. Run the system. 2. Make sure there is no Thermal Trip false alarm. 2. Category: Fix Description: [61067] 10G AOC Temp is misbehave when both 10G & 40G populate on certain slots order Infected motherboard: All platform except motherboards with Denlow CPU Affected functions: Validation : 1. Power off the system. 2. Insert 10G and 40G AOC cards at the same time. 3. Power on the system. 4. Check the sensor reading page. 5. Power off the system. 6. Switch 10G and 40G AOC cards. 7. Power on the system. 8. Check the sensor reading page. 3. Category: Fix Description: [60364] User privilege access errors. Infected motherboard: All Affected functions: Validation : 1. Compare the privilege with Spec. 2. Since AST2400 provides multi session, we cannot support ikvm as view only (Change it from View only to No). 4. Category: Fix Description: [61198] [BIOS & ECO]RT2 no Fan control. Infected motherboard: X10SRG Affected functions: Validation : 1. Heat and Cool the RT2. 2. Check Fan1~4 behavior. 5. Category: Fix Description: [61219] [IPMI FW 1.94 - Power consumption page] Maximum is misspelled in IPMI Web GUI Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run the system. 2. Check the power consumption page. 6. Category: Fix Description: [61137] When unplug the whole power supply module from the system, the IPMI does not report loss of power/ power supply missing to the IPMI event log Infected motherboard: X10 motherboards with more than 2 redundant power supplies Affected functions: Validation : 1. Install 2 power supplies and let bmc boots up. 2. Pull out one power suppy module with ac cords together. 3. Check de-asserted log if happens. 4. Plug in this power supply module 5. Check de-asserted log if happens. 7. Category: Fix Description: [61193] [K40 GPUs] Only one GPU temperature is shown in IPMI Web GUI when several Tesla K40s are installed [61079] The fan sensor names don't match the silkscreen Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run the system. 2. Check the sensor reading page. 8. Category: Fix Description: [61192] No Xeon Phi temperature sensor readings are shown in IPMI Web GUI for Intel Xeon Phi 7120P Infected motherboard: X10DRG-O+-CPU-O-P/X10DRG-OT+-CPU-O-P Affected functions: Validation : 1. Run the system. 2. Check the sensor reading page. --------------------------------------------------------------------------------------------- Filename: SMT_X10_194.bin version: 1.94 Date: 04-08-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [60690] [NVMe] No NVMe Tab available in IPMI Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Plug in AOC-URN6-I2XT-O-P and test NMVE functions 2. Category: Fix Description: [60779][IPMI firmware v1.93 ECO] No CPU Thermal Trip Event Log Loging in IPMIWeb GUI Infected motherboard: X10QBi Affected functions: Validation : 1. Heat the CPU to system shut down. 2. Check the event log. 3. Category: Fix Description: [58593][EVT] Missing Thermal Trip Event Log on IPMI Web. Infected motherboard: X10QRH+ Affected functions: Validation : 1. Heat the CPU to system shut down. 2. Check the event log. 4. Category: Fix Description: Upgrade OpenSSL to version 1.0.1m to include CVE fixes (CVE-2015-0204, CVE-2015-0286, CVE-2015-0287, CVE-2015-0289, CVE-2015-0292, CVE-2015-0293, CVE-2015-0209 and CVE-2015-0288). Infected motherboard: All Affected functions: Web GUI Validation : 1. Start firmware update and see if image is correctly downloaded and New Version information can be seen. 2. Repeat step 1 using IE, Firefox and Chrome in Windows; Firefox and Chrome in Ubuntu 14.04. 5. Category: Fix Description: Change default SSL key length from 1024 to 2048 bits. Infected motherboard: All Affected functions: Web GUI Validation : 1. Do restore to Factory Default after firmware update. 2. Login to web server through https, and check the key lenght. Steps can be found in: (http://windowsitpro.com/security/are-your-ssl-certificates-secure) 6. Category: Fix Description: [60230][DVT] BIOS and IPMI Event log Cannot Report the correct DIMM Location While Doing Rastool C-ECC and U-ECC Error Injection. Infected motherboard: X10QRH+ Affected functions: Validation : 1. Generate C-ECC and U-ECC event. 2. Check the event log. 7. Category: Fix Description: [60875]Lost all memory sensor reading again. Infected motherboard: X10QBi Affected functions: Validation : 1. Run the C-burn test. 2. Check the Memory and CPU temperature reading. 8. Category: Fix Description: [60901]CPLD display need to be in raw HEX with period separator. [60902]BIOS & IPMI FW does not follow CPLD display rule. Infected motherboard: All except motherboards with Denlow CPU Affected functions: Validation : 1. Log in the WebGui. 2. Check the CPLD version, it should be xx.xx.xx. 9. Category: Fix Description: [NVMe] No NVMe Tab available in IPMI Infected motherboard: X10DRU-I+. Use AOC-URN6-I2XT and RSC-UN4-88 Affected functions: Validation : 1. Insert 10 NVMe cards and install AOC-URN6-I2XT. 2. If you install RSC-UN4-88 card, please use HW 1.01 version 3. Chck NVMe web gui 10. Category: Fix Description: [60803]AOC-S40G-i2Q temperature sensor reading does not show under IPMI webgui. Infected motherboard: X10QBi Affected functions: Validation : 1. Insert the AOC-S40G-i2Q onto the PCIe slot. 2. Power on the system and wait it boots to the OS. 3. Check the 40G temp sensor. 11. Category: Fix Description: Block PMBUS access while doing any kind of firmware update to avoid PS FRU corruption. Infected motherboard: All Affected functions: Validation : 1. Get pminfo through SMCIPMITool with correct result. 2. Start BIOS update through Web, then repeat step 1. This time SMCIPMITool will get "Cannot detect slave address" error message. 12. Category: Fix Description: Block PMBUS access while doing any kind of firmware update to avoid PS FRU corruption. Infected motherboard: All Affected functions: Validation : 1. Get pminfo through SMCIPMITool with correct result. 2. Start BIOS update through Web, then repeat step 1. This time SMCIPMITool will get "Cannot detect slave address" error message. 13. Category: Fix Description: [60559] Fan staying at 1,200 rpm after the other fan is unplugged and CPUs overheat Infected motherboard: X10DRT-P Affected functions: Validation : 1. Let fan fail happens and the sytem will do full speed 2. power reset 3. check if fan speed keeps full speed 14. Category: Fix Description: Update LCMC functiion failed on 1.92 Infected motherboard: X10DRT-P Affected functions: Validation : 1. Try to update lcmc function on IPMI web gui 15. Category: Fix Description: [60336] Fan duty cycle is much higher than reference defined in thermal guide. Infected motherboard: X10DRU-i+ Affected functions: Validation : 1. Heat the test sensors. 2. Compare the duty cycle and temperature. (Refer the thermal guide.) 3. It should be almost the same. ------------------------------------------------------------------------------------------ Filename: SMT_X10_193.bin version: 1.93 Date: 03-26-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [60152] False mesages about CPUs & Vcpus under IPMI SEL. Infected motherboard: X10QBI Affected functions: Validation : 1. Put the Haswell CPU into the system. 2. Power on the system. 3. Check the SEL. 2. Category: Fix Description: [60566] [IPMI ECO v1.91] Chassis Intrusion Email Event Description Wrong. Infected motherboard: All Affected functions: Validation : 1. Generate Chassis Intrusion Event. 2. Check the email words. 3. Category: Fix Description: [59863][DVT] No GPU Temperature Sensor Reading On IPMI Web. Infected motherboard: X10QRH+ Affected functions: Validation : 1. Please use Rev 1.01 or above motherboards. 2. Please use X10QRH5.318 or later BIOS. 3. Insert the GPU cards, power on the system. 4. Wait the system boots to OS. 5. Check the GPU Temperatures. 4. Category: Fix Description: [60718 ][BIOS ECO] Lost sensor readings on RSC-R2UW-2E8E16+ Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Inset AOC-S3108-H8iR on (slot3) 2. Check if IPMI web can see LSI sensor and Storage Monitoring web page 5. Category: Fix Description: [60596] Function fail: The hardware monitor some item can't be detect. Infected motherboard: X10SDV Affected functions: Validation : 1. Check if has PCH Temp value. ------------------------------------------------------------------------------------------ Filename: SMT_X10_192.bin version: 1.92 Date: 03-16-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [60420] Can't Update BIOS From WebGUI with IPMI FW 1.90 and 1.91. [60340] [IPMI ECO] Cannot Complete BIOS Flashing on IPMI Web GUI. [60341] [IPMI ECO] Cannot Complete BIOS Flashing on IPMI Web GUI. [60327] Cannot complete BIOS Update process via IPMIWeb with IPMI v1.90 & v1.91. Infected motherboard: X10SLH, X10SLM+, X10SLL, X10SL7, X10SLM-LN4F Affected functions: Validation : 1. Login the WebGUI. 2. Update the BIOS image 3. It should 100% complete. 2. Category: Fix Description: [60404] Some issues on IPMI Sensor Readings. Infected motherboard: X10SDV-F Affected functions: Validation : 1. Power-on the system. 2. Check the sensor list. 3. Category: Fix Description: [60430] Temp. Reading for AOC-S40G-i2Q is missing in IPMI v1.91 Infected motherboard: A1SA7, X10DRU-I+ Affected functions: Validation : 1. Power-on the system and plug in 40G AOC card 2. Check the sensor list. 4. Category: New Feature Description: Show CPLD Revision infomation on the WebGUI Infected motherboard: X10DRI-T Affected functions: Validation : 1. Login the WebGUI. 2. Show the CPLD Revision: AA BB CC. 5. Category: New Feature Description: Show CPLD Revision infomation on the WebGUI Infected motherboard: X10DRI-T Affected functions: Validation : 1. Login the WebGUI. 2. Show the CPLD Revision: AA BB CC. 6. Category: Fix Description: [60339] The optimal fan curve doesn't satisfy the required curve in thermal guide Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Check the optimal mode FSC of CPU if it meets thermal guide 4.04 specificaiton ------------------------------------------------------------------------------------------- Filename: SMT_X10_191.bin version: 1.91 Date: 03-06-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [60291] After open iKVM console, IPMI unstable. [60163] After open iKVM console, IPMI unstable. Infected motherboard: All Affected functions: Validation : 1. Open iKVM first. 2. Press IPMI function item. (Ex: Power Control, Sensor Reading) 3. Screen show normal information. 2. Category: Fix Description: [58593] [EVT] Missing Thermal Trip Event Log on IPMI Web Infected motherboard: All Affected functions: Validation : 1. Let other CPUs enter thermal trip 2. Check IPMI sel log 3. Category: Fix Description: [58537] The Fan speed doesn't go down when the HDD temperature goes down. Infected motherboard: X10QBI Affected functions: Validation : 1. Change the fan mode from Standard to Full. See the fans become full speed or not. 2. Change the fan mode from Full to Heavy IO. See the fan behavior. 3. Change the fan mode from Heavy IO back to Standard. See the fan behavior. 4. Category: Fix Description: [60276] Can't mount the ISO file on the webgui [59877] Invalid Image path. Infected motherboard: All Affected functions: Validation : 1. Input correct data into each column. (Ex: path:\xxx\xxxx\xxx.ISO) 2. Check the function is fine. 3. Change the ISO file to zip file. 4. Check the error message. 5. Category: Fix Description: [59853] Normal Open iKVM successfully when updating BIOS. Infected motherboard: All Affected functions: Validation : 1. Open the ikvm in Laptop A. 2. Update the BIOS in Desktop B. 3. Check the ikvm of Laptop A should be closed. 6. Category: Fix Description: [60206] HeavyIO mode FAN speed is incorrect. Infected motherboard: X10SLM-LN4F Affected functions: Validation : 1. Change the Fan mode to HeavyIO mode. 2. Check the fan speed of zone1 fans. --------------------------------------------------------------------------------- Filename: SMT_X10_190.bin version: 1.90 Date: 02-17-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [59968] Thermal trip event logged. Infected motherboard: X10DRU-i+ Affected functions: Validation : 1. After upgrading the FW, power on the system. 2. Check the power on process is done, power off the system. 3. Check the SEL Log. It should not have Processor #4 Theraml Trip SEL. 2. Category: Fix Description: Set theshould on 3.3VSB sensor (HCT = 3.539, HC=3.659, HNR= 3.689) Infected motherboard: A1SA2 Affected functions: Validation : 1. Check sensor reading 3. Category: Fix Description: 3.3VSB sensor value is between LNC and LC on IPMI 1.88 Infected motherboard: A1SA2 Affected functions: Validation : 1. Check if this value is above LNC. 4. Category: New Feature Description: RT2 temperature is equal to PCH's - 4 on V1.01 and V.102A motherboard Otherwise, it read from winbond chip. Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Check if HW motherboard version is written in fru1 2. Observe RT2 temperature and PCH temperature on your motherboard ------------------------------------------------------------------------------ Filename: SMT_X10_189.bin version: 1.89 Date: 02-11-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [59537] NVMe information missing in IPMI WebGUI Infected motherboard: X10DRU-i+ Affected functions: Validation : 1. Login the webgui and power on the system. 2. Go to the sensor reading page and check the NVMe sensor temperature. 3. Go to the NVMe SSD page and check the information. 2. Category: Fix Description: [59118] IPMI/BIOS Hardware Monitor Check Failed. Infected motherboard: X10QRH+ Affected functions: Validation : 1. Compare the IPMI reading value with DMM reading. (Error should be under 5%) 3. Category: Fix Description: [59508] BIOS Hardware Monitor Check fail. Infected motherboard: X10SRD Affected functions: Validation : 1. Compare the IPMI reading value with DMM reading. (Error should be under 5%) 4. Category: Fix Description: [59646] [DVT] IPMI Web Always Shown as "Warning" Event When All Sensors Are Presented OK. Infected motherboard: X10QRH+ Affected functions: Validation : 1. Login the webgui and check right hand side of top menu. 5. Category: Fix Description: FAN1 fan fail has problem Need to remove FAN7 sensor Infected motherboard: X10DRG-Q Affected functions: Validation : 1. Install FAN1 and remove it for fan-failed test 2. Check no FAN7 sensor on IPMI web gui 6. Category: Fix Description: [59770] No Power Suppy Information Found in IPMI Web GUI Hardware Information Infected motherboard: All Affected functions: Validation : 1. Insert power supply 2. Check IPMI hardware information web page 3. It needs bios' s support if you does not see power supply informaton and the total numbers of power supplies are not correct 7. Category: Fix Description: [59805] [DVT] Missing "Smart Cooling", "PUE2" & "PUE3" Fan Speed Control Mode In IPMI Web Infected motherboard: X10QRH+, X10DRU+ Affected functions: Validation : 1. Check IPMI Webpage - Fan Control Page. 8. Category: Fix Description: [59420] IPMI TimeStamp always is "1970/01/01" in IPMI Event Log page Infected motherboard: X10SDV Affected functions: Validation : 1. After updating IPMI FW, power cycle the system. 2. After booting to OS, generate a SEL and see its timestamp is correct or not. 9. Category: Enhancement Description: Change VBAT sensor thresholds (HNC=3.6V, HC=3.7V, HR=3.8V, Tom Xiao's suggestion) Infected motherboard: A1SA2 Affected functions: Validation : 1. Check VBAT sensor thresholds on IPMI web gui 10. Category: Fix Description: Fix the bug, when "Timeout Value for graceful shutdown" input is over 255. It does not work Infected motherboard: Motherboard which suuport bbp function Affected functions: Validation : 1. Connect power supplies and bbp with your motherboard 2. Input value over 255 on gracefual shutdown option 3. Press Save button and refresh the web gui 4. Check if value is still the same as input 11. Category: Fix Description: Support Expander On-die temperature and FSC Infected motherboard: X10DRT-P Affected functions: Validation : 1. use BPN-ADP-E1C-L 2. Expander sensor will be shown on sensor reading web page 3. The FSC is the same as 10G sensor. Please heat it and check FSC ------------------------------------------------------------------------------ Filename: SMT_X10_188.bin version: 1.88 Date: 01-26-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: Enlarge VBAT voltage to avoid false event log Infected motherboard: A1SA2 Affected functions: Validation : 1. Do SAT or LAN test to check if false event log launch 2. Category: Fix Description: [59315] Time stamp on power consumption page not shown correctly Infected motherboard: All Affected functions: Validation : 1. Login the webgui and goto power consumption page. 2. Check the time stamp. 3. Category: Fix Description: Node1 sensors are missing on IPMI web gui Infected motherboard: A1SA2 HW 1.01 version Affected functions: Validation : 1. Check IPMI sensor reading web gui 4. Category: New Feature Description: Add Config_ID into the Multi-node function. Infected motherboard: Twin series Affected functions: Multi-Node function. Validation : 1. Login the Webgui. 2. Check the Multinode page. 5. Category: Fix Description: [59401] Fans do not change speed at all. Infected motherboard: X10QBi Affected functions: Validation : 1. Login the webgui and set the fan mode to full speed. 2. Make one fan fail and check the fan speed of other fans. 6. Category: Fix Description: [59004] [DVT] Onboard buzzer keep beeping after CPU2 cooled down to normal temperature from overheat. Infected motherboard: X10QRH+ Affected functions: Validation : 1. Make the CPU overheat and hear beeping. 2. Cool down the CPU, and check the beeping is stop. 7. Category: Fix Description: [58537] The Fan speed doesn't go down when the HDD temperature goes down. Infected motherboard: X10QBI Affected functions: Validation : 1. Change the fan mode from Standard to Full. See the fans become full speed or not. 2. Change the fan mode from Full to Heavy IO. See the fan behavior. 3. Change the fan mode from Heavy IO back to Standard. See the fan behavior. 8. Category: Fix Description: [59386] Standard speed mode is missing from IPMI fan mode setting menu Infected motherboard: X10DRD, X10DRD-L Affected functions: Validation : 1. Check fan mode 9. Category: Fix Description: Support on-board mux function Infected motherboard: X10DRX Affected functions: Validation : 1. Plug in LSI3108 card on Slot1-8. 2. Power on and check if SAS sensor can be seen on IPMI sensor reading web page 10. Category: Enhancement Description: Support Expander On-die temperature and FSC Infected motherboard: X10DRT-P Affected functions: Validation : 1. use BPN-ADP-E1C-L 2. Expander sensor will be shown on sensor reading web page 3. The FSC is the same as 10G sensor. Please heat it and check FSC 11. Category: Work around Description: Support 1.01B X10SRL cpu & memory & 1.01B X10SRI cpu vrm sensor readings Infected motherboard: X10SRL & X10SRI Affected functions: Validation : 1. Check the vrm sensor reading on X10SRL 1.01B & X10SRI 1.01B 2. Also, please check the older motherboard version, X10SRL 1.01 & X10SRI 1.01 12. Category: Fix Description: [59507] X10DRT-L sensor reading has "IB temp" item show N/A Infected motherboard: X10DRT-L Affected functions: Validation : 1. update new bios which will tell bmc IB sensor is on the motherboard 2. Check the sensor reading web gui 12. Category: Security Fix Description: ICMP timestamp issue Infected motherboard: All Affected functions: Validation : 1. please use Retina network security scanner to scan IPMI fw. -------------------------------------------------------------------------- Filename: SMT_X10_187.bin version: 1.87 Date: 01-14-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Enhancement Description: Add Preserve SDR checkbox on Firmware upload web page Infected motherboard: All Affected functions: Validation : 1. Uncheck this option, the old SDR will be removed after new FW is updated 2. Category: Fix Description: [58968] IPMI Set "PW consumption" Sensor Reading Low Limit Value Too High (IPMI FW:1.85) Infected motherboard: X10DRT-P Affected functions: Validation : 1. Observe "PW consumption" Sensor. High non-recoverable values should be higher than High crtital value 3. Category: Work around Description: Let RT2 value is equal to (PCH - 4) value Infected motherboard: X10DRU-+ Affected functions: Validation : 1. After IPMI FW is updated, use this command to remove old SDR SMCIPMITool.exe 10.133.176.225 ADMIN ADMIN ipmi raw 30 44 2. Check if RT2 value is equal to (PCH-4) value 4. Category: Fix Description: [59198] CPU FSC cannot meet thermal guide SIM_TDG REV. 4.04 (11192014) Infected motherboard: X10DRD-L Affected functions: Validation : 1. Check CPU PUE3 FSC meets thermal guide 4.04 -------------------------------------------------------------------------- Filename: SMT_X10_186.bin version: 1.86 Date: 01-xx-2015 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58968] IPMI Set "PW consumption" Sensor Reading Low Limit Value Too High (IPMI FW:1.85) Infected motherboard: X10DRT-P Affected functions: Validation : 1. Observe "PW consumption" Sensor reach low Limit values. 2. Category: Fix Description: [58971] IPMI monitor: RT1/RT2 Temperature Reading fail. Infected motherboard: X10DRD series Affected functions: Validation : 1. Check the IPMI reading with the thermalmeter reading. 3. Category: Fix Description: [58977] No option of PUE3 mode. Infected motherboard: X10DRD series Affected functions: Validation : 1. Check the Fan mode page of WebGUI. 4. Category: Fix Description: [59003] Optimal Fan Speed Mode not Working. Infected motherboard: X10DRH-IT Affected functions: Validation : 1. Heat the 10G Temperature sensor. 2. Observe the FAN speed. (Zone 1 should not change. Zone 2 should rise.) 5. Category: Fix Description: Enlarge 5VSTB and 3.3VSTB voltage to avoid false event log Infected motherboard: A1SA2 Affected functions: Validation : 1. Do SAT or LAN test to check if false event log launch 6. Category: Fix Description: Support GPU3 sensor on both Left & Right Cooling zone Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Heat GPU3 sensor and let it to dominate left zone and rigth zone 2. check fan speed is going high on both left zone and right zone -------------------------------------------------------------------------- Filename: SMT_X10_185.bin version: 1.85 Date: 12-31-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58766] X10DRC-LN4 IPMI ECO 1.80 Improvement Item #1 Infected motherboard: X10DRC Affected functions: Validation : 1. Heat SAS and let it over 105 degree 2. The sensor status over 105 degree should be "Upper Non-recoverable" 2. Category: Fix Description: [58807] [NM] Can't get entire platform CPU power statistics. Infected motherboard: X10DRT-L Affected functions: Validation : 1. try 0x30 0xe2 command. It should return non-zero value 3. Category: Fix Description: [58641] The IPMI Sensor readings test fail. Infected motherboard: X10SDV Affected functions: Validation : 1. HW need to rework the DP, DN to 10G NIC. 2. Check the 10G sensor reading 4. Category: Fix Description: [58708] [ECO] IPMI v1.82 Cannot Define the Correct Multi-Node Position. Infected motherboard: X10DRT-P Affected functions: Validation : 1. Login the Webgui and go to Multi Node page. 2. Check the node status. 5. Category: New Feature Description: InfiniBand Temperature Reading Infected motherboard: X10DRT-L Affected functions: InfiniBand Temperature Sensor Validation : 1. Power up MB and check if IB Temp is available. 6. Category: Work around Description: lower down the link speed to 100M for X10SLE / X10SLD Infected motherboard: X10SLE / X10SLD Affected functions: S5 state Validation : 1. Check if dedicate lan speed is 100Mbps at S5 state -------------------------------------------------------------------------- Filename: SMT_X10_184.bin version: 1.84 Date: 12-24-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58537] The Fan speed doesn't go down when the HDD temperature goes down. Infected motherboard: X10QBI Affected functions: Validation : 1. Change the fan mode from Standard to Full. See the fans become full speed or not. 2. Change the fan mode from Full to Heavy IO. See the fan behavior. 3. Change the fan mode from Heavy IO back to Standard. See the fan behavior. 2. Category: Fix Description: [58690] IPMI Hardware Monitor Check fail Infected motherboard: X10DRT-L Affected functions: Validation : 1. Check VBAT sensor on IPMI sensor reading web page 3. Category: Fix Description: Decrease -5 degree on RT2 sensor Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Check RT2 4. Category: Fix Description: Insert 4 Xeon Phi GPUs and let it idle, sometimes GPU sensors are gone Infected motherboard: X10DRG-Q. Affected functions: Validation : 1. Insert 4 Xeon Phi GPUs and put it idle 2. Check if GPU sensors are still gone -------------------------------------------------------------------------- Filename: SMT_X10_183.bin version: 1.83 Date: 12-18-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58621] VcpuVRM temperature shows "not-present" w/ rev 1.02 board. [58650] [VRM change to MPS] Missing IPMI VRM temp sensor reading of VcpuVRM temp and VmemVRM temp. Infected motherboard: X10DRU-i+, X10DRI-T Affected functions: Validation : 1. Power on the system. 2. Check the VcpuVRM sensor reading. 2. Category: Fix Description: [58637] IPMI FW not ready Infected motherboard: X10DRD-L Affected functions: Validation : 1. Check IPMI sensor web gui 3. Category: Fix Description: [58630] AOC-2UR66-i4G does not show GPU temperature Infected motherboard: X10DRU-+ Affected functions: Validation : 1. Check IPMI sensor web gui 4. Category: Fix Description: [58341] The IPMI sensor readings test fail. Infected motherboard: X10SDV Affected functions: Validation : 1. Check the VBAT sensor reading. It should be close to the DMM reading. 5. Category: Add new feature Description: Add Thermal trip Infected motherboard: X10DRU-+ Affected functions: Validation : 1. Remove fan and heat sink from CPU1 or CPU2. 2. Wait platform to shot down. 3. Check thermal trip event log. 6. Category: Support PUE2b Fan mode Description: Add Thermal trip Infected motherboard: X10DRU-+, X10DDW, X10DRFF Affected functions: Validation : 1. Check PUE FSCs on CPU, DIMM, PCH, 10G, SAS -------------------------------------------------------------------------- Filename: SMT_X10_182.bin version: 1.82 Date: 12-12-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58437] IPMI isn't offline when send warm reset command. Infected motherboard: All Affected functions: Validation : 1. Issue the command: ipmitool -H -U ADMIN -P ADMIN mc reset warm 2. Wait about 10 seconds. 3. Issue any IPMI commands should not be worked. 4. Wait about 100 seconds. 5. Issue IPMI commands should be fine. 2. Category: Fix Description: [58363] F-SKU reacts dual cooling zone behavior. [58376] F-SKU reacts dual cooling zone behavior. Infected motherboard: X10SRA, C7X99 Affected functions: Validation : 1. Change the fan mode to Heavy IO mode. 2. Check the fan zone behavior. 3. Category: Fix Description: [56888] [Haswell] Vcpu1,2,3,4 reading status are shown as Upper Critical. Infected motherboard: X10QBI Affected functions: Validation : 1. Please update BIOS to the X10QBi14.HSX.C10. 2. Put the Haswell CPU onto the X10QBI. 3. Check the Vcpu sensor readings. 4. Category: Fix Description: [58341] The IPMI sensor readings test fail. Infected motherboard: X10SDV Affected functions: Validation : 1. Check the VBAT sensor reading. It should be close to the DMM reading. 5. Category: New Motherboard Description: Add new motherboard: X10QRH+. Infected motherboard: X10QRH Affected functions: Validation : 1. IPMI bring up version. -------------------------------------------------------------------------- Filename: SMT_X10_181.bin version: 1.81 Date: 12-xx-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58242] [JC2] Vcpu reading is incorrect in IPMI Sensor Reading page. Infected motherboard: X10QBL Affected functions: Validation : 1. Please update BIOS to the latest version. 2. Put the Haswell CPU onto the X10QBL. 3. Check the Vcpu sensor readings. 2. Category: Fix Description: [57381] Existing BIOS shows "UNKNOWN" while updating BIOS via web-page. Infected motherboard: A1SRM-LN7F Affected functions: Validation : 1. Update the BIOS from WebGUI. 2. Check the current build date. 3. Category: Fix Description: [58345] Whran trying to re-insert NVME, slot number is missing. Infected motherboard: X10DRU-i+ Affected functions: Validation : 1. Eject the SSD. 2. Insert the same one SSD. 3. Check the page information. 4. Category: Fix Description: [58363] F-SKU reacts dual cooling zone behavior. [58376] F-SKU reacts dual cooling zone behavior. Infected motherboard: X10SRA, C7X99 Affected functions: Validation : 1. Change the fan mode to Heavy IO mode. 2. Check the fan zone behavior. -------------------------------------------------------------------------- Filename: SMT_X10_180.bin version: 1.80 Date: 12-02-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57441] AOC SAS Card overheat but no error sensor. Infected motherboard: All motherboard support AOC SAS Card Affected functions: Validation : 1. Heat the AOC SAS card. 2. Make the temperature over 95 degree C. 3. Check the AOC_SAS_Temp sensor color is changed. 4. Check the SEL. 2. Category: Fix Description: [57986] There are multiple devices under IPMI webgui PCIe SSD page. Infected motherboard: All motherboard support NVMe Affected functions: Validation : 1. Keep only one NVMe device on board. 2. Power on the system and check the NVMe SSD page. 3. It should only have one Device:0. 3. Category: Fix Description: [56888] [Haswell] Vcpu1,2,3,4 reading status are shown as Upper Critical. Infected motherboard: X10QBI Affected functions: Validation : 1. Please update BIOS to the latest version. 2. Put the Haswell CPU onto the X10QBI. 3. Check the Vcpu sensor readings. 4. Category: Fix Description: [58234] SYS-1028TR-TF system power red LED blinks fail [58231] IPMI sensor readings power status fail [58206] IPMI Sensor readings fail Infected motherboard: X10DRT-L Affected functions: Validation : 1. Check IPMI sensor web gui 2. Check the fuction when power fail 5. Category: Fix Description: [58268] IPMI cannot provide K80 GPU Temp Infected motherboard: X10SRG Affected functions: Validation : 1. Check IPMI sensor web gui 2. Check if GPU sensors present 6. Category: Fix Description: [58180] No Dimm C2,D2 in sensor reading. Infected motherboard: A1SA2 Affected functions: Validation : 1. Do factory default after new IPMI FW is downloaded 2. Check if dimm sensors present 7. Category: Fix Description: [58286] AOC-S40G-i2Q isn't display on sensor reading [58275] o HDD in sensor reading Infected motherboard: A1SAM Affected functions: Validation : 1. Use lastest BIOS which can send 0x3a and 0x5a commands 2. Set JI2C1 JI2C2 jumpers to 1-2. 3.Plug in 40G card and power on the system 4.Check if 40G LAN card sensor appear 5.Repeat step 3, Plug in LSI 3108 cards and power on the sytem 6.Check if SAS sensors shows 8. Category: Fix Description: [58242] [JC2] Vcpu reading is incorrect in IPMI Sensor Reading page. Infected motherboard: X10QBL Affected functions: Validation : 1. Please update BIOS to the latest version. 2. Put the Haswell CPU onto the X10QBL. 3. Check the Vcpu sensor readings. ------------------------------------------------------------------------------------------ Filename: SMT_X10_179.bin version: 1.79 Date: 11-21-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [58041] Cancelling during ejection will appear to hang at "Cancelling" Screen [58037] Cancelling Eject will show the same pop up window as Ejecting [58035] The Help Page displays incorrectly for "NVMe SSD" [58033] Wording was not changed from "Inject" to "Insert" [58019] IPMI NVMe message still exist when a system shutdown state [57953] IPMI NVMe SSD Page: Slot Pull-down Tab is Not Function Infected motherboard: All motherboards with NVMe devices installed Affected functions: Validation : 1. Eject & Insert the NVMe device on NVMe web gui 2. Verify the wording 3. Check help page 4. When system is powered on. The NVMe web information will be hidden. Later user logins IPMI web, no NVMe web page 5. Try to pull down the Slot Pull-down Tab, the function should work as pulling down the Device Pull-down Tab 2. Category: Fix Description: [57861] Deactivating Activate Smart Cooling shows false fan mode Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Do factory default after FW is downloaded 2. Check if the smart cooling mode is disable 3. Select smart cooling mode and save 4. Uncheck the smart cooling mode option 5. Check if PUE2 mode is selected 3. Category: Fix Description: [57980] The Fan speed doesn't change when I heat the HDD. Infected motherboard: X10QBI Affected functions: Validation : 1. Heat the HDDs. 2. Check the fan speed is rising or not. 4. Category: Fix Description: [57799] IPMI on/off will lose IPMI sensor readings Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Do System On/Off test 2. Check the sensors status show "No present" after system is powered on 5. Category: Fix Description: [58105] There is no "Processor Automatically Throttled" event log. Infected motherboard: X10DBT-T Affected functions: Validation : 1. Heat the CPU to processor hot. 2. Check the "Processor Automatically Throttled" event log. 6. Category: Fix Description: [58100] AOC-2UR68-i2XS does not provide GPU sensor readings Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Install GPUs and let system power on 2. Check if GPU sensor displays on IPMI sensor web gui 7. Category: Fix Description: [58065] Multinode page failed to show node B when viewed from Node A Infected motherboard: X10DRFR Affected functions: Validation : 1. Login in node A 2. Check the node B informaiton is not missing on multi-node web gui 8. Category: Fix Description: [57373] IPMI sensor readings shows "2 X AOC_40G Temp" when "2 X AOC_10G " cards plugged in Infected motherboard: X10DDW Affected functions: Validation : 1. Plugin 2 AOC_10G cards with new riser RSC_R2UW_2E8E16+ 2. Check the IPMI web gui, it should show "AOC_10G" sensor name ------------------------------------------------------------------------------------------ Filename: SMT_X10_178.bin version: 1.78 Date: 11-17-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: Add a confirmation message after ??Eject?? button is clicked Change the wording from ??Inject?? to ??Insert?? Infected motherboard: All motherboards with NVMe devices installed Affected functions: Validation : 1. Update the IPMI FW. 2. Check NVMe web gui 2. Category: Enhancement Description: Default fan mode is PUE2 mode on X10DRU-+ Infected motherboard: All motherboards with NVMe devices installed Affected functions: Validation : 1. Update the IPMI FW. 2. Do factory default ------------------------------------------------------------------------------------------ Filename: SMT_X10_177.bin version: 1.77 Date: 11-12-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57854] [IPMI V1.75 ECO] IPMI Share LAN Status show "Disabled" when IPMI link by onboard LAN1 Infected motherboard: X10SRA, C7X99, C7Z97 Affected functions: Validation : 1. Update the IPMI FW. 2. Restore to Factory Default by command: 0x30 0x41 3. Power Cycle the SUT. 4. Check the LAN Link status in IE Browser. 2. Category: Fix Description: [57866] IPMI Cannot Define Correct Current-Node Position Under Multi-Node Page Infected motherboard: X10DRT-P Affected functions: Validation : 1. Setup two node and power up together 2. Check multinode web page of node A 3. Check if current node is node A, not node B 3. Category: Fix Description: [57847] [IPMI V1.75 ECO] Sometimes ACPI Status cannot sync up in "Power Control and Status" Page. Infected motherboard: X10SRA, C7X99, C7Z97 Affected functions: Validation : 1. Power on/off the SUT. 2. Wait serveral seconds and check the power status in the same page. 4. Category: Fix Description: [57589] IPMI Web GUI still showing NVMe drive information and Eject option after successfully ejected NVMe SSD [57588] IPMI Web GUI still showing NVMe drive information and Eject option after successfully ejected NVMe SSD Infected motherboard: X10 Grantley motherboard with NVMe device installed Affected functions: Validation : 1. If user clicked on the eject icon and did not unplug the NVMe drive, 2. IPMI should not show NVMe drive information on IPMI web gui 5. Category: Fix Description: [56411] I loose all PCI_SSD tab info when I plug in "samsung NVMe SSD" in system Infected motherboard: X10 Grantley motherboard with Samsung NVMe device installed Affected functions: Validation : 1. Install Samsung NVMe drive 2. Check if the information displays on the IPMI web gui ------------------------------------------------------------------------------------------ Filename: SMT_X10_176.bin version: 1.76 Date: 11-06-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57789] After reload IPMI configuration, IPMI Configuration can be reloaded, but will generate unknown message in IPMI Configuration page Infected motherboard: All Affected functions: Validation : 1. After reload IPMI configuration 2. No unkown message on IPMI Configuration page 2. Category: Fix Description: X10QBi BMC would be reboot issue. Infected motherboard: X10QBi Affected functions: Validation : 1. Running cburn test, Blink the UID LED 2. Check the UID LED keeps blinking continually in the test. 3. Category: Fix Description: [57691] [IPMI] When updating the FW in WEB GUI, the process stops at 93% instead of 100% Infected motherboard: X10DDW Affected functions: Validation : 1. Update the FW and check the update progress. 4. Category: Add new feature Description: Add Thermal trip Infected motherboard: X10DRH Affected functions: Validation : 1. Remove fan and heat sink from CPU1 or CPU2. 2. Wait platform to shot down. 3. Check thermal trip event log. 5. Category: Add new feature Description: 1. Add two sensors, HDD status and HDD Temp. respectively for LSI controller. 2. Fan control on HDD Temp. according to the thermal guide. Infected motherboard: Affected functions: Validation : 1. Check HDD Temp in sensor reading page 2. Heat up HDD temperature. 3. Monitor the fan speed changing. 6. Category: Fix Description: [57841] CPU1 temp and CPU2 temp are still shown in multinode monitoring page when restarting system [57826] IPMI Multinode Temperature reading shows CPU1 at 101 Degrees C when powering on the system Infected motherboard: X10DRFR Affected functions: Validation : 1. Enter multinode IPMI web gui 2. Do power off & power on another mode 3. Check if CPU1 Temp, CPU2 Temp information, it will show N/A during BIOS POST ------------------------------------------------------------------------------------------ Filename: SMT_X10_175.bin version: 1.75 Date: 10-31-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57369] FAN PWM measurement fail for Memory. Infected motherboard: X10QBL Affected functions: Validation : 1. Heat the memory. 2. Use the scope to see the duty cycle waveform. 2. Category: Fix Description: [56798] System will generate a lot of error event when run E-burn stress test. Infected motherboard: X10QBL Affected functions: Validation : 1. Run the E-burn test 2. Check the SEL, CPU Voltages and CPU Temperatures. 3. Category: Fix Description: [56082] IPMI sensor has no PCH Temp and VRM Temp is N/A. Infected motherboard: X10SRA Affected functions: Validation : 1. Go to the Sensor list page of Webgui or issue the ipmitool sensor list command. 2. Check the VcpuVRM Temp reading. 4. Category: Fix Description: Memory reading issue on Intel C1 stepping CPU. Infected motherboard: X10SRI, X10DRI-T Affected functions: Validation : 1. See the Sensor list page of Webgui or issue the ipmitool sensor list command. 5. Category: Fix Description: [57371] Unusual IPMI events logged. Infected motherboard: X10DRU-X Affected functions: Validation : 1. Run the stress test under windows server 2K8 over night. 2. Check the chassis_intru event is generated or not. 6. Category: Fix Description: [57703] FAN PWM measurement fail for Memory on PUE3 mode [57702] FAN PWM measurement fail for RT2 at PUE3 mode Infected motherboard: X10DRFF, X10DDW, X10DDW-IN, X10DRU-+ Affected functions: Validation : 1. Check PUE3 FSC is the same as PUE2 FSC 7. Category: Enhancement Description: Change the default fan mode is Standard mode Infected motherboard: X10DRT-P, X10DRFF Affected functions: Validation : 1. Do factory default action 2. Check if the default fan speed is standard mode 8. Category: Fix Description: The VBAT sensor will reproduce abnormal SEL Infected motherboard: A1SA2 Affected functions: Validation : 1. Do bmc coldreboot on node1 2. Do bmc coldreboot on node2 3. Checek the event log. It should not be reproduced ------------------------------------------------------------------------------------------ Filename: SMT_X10_174.bin version: 1.74 Date: 10-27-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57225] NO AOC Temp reading when JPI2C is enabled Infected motherboard: A1SA7 Affected functions: Validation : 1. Check if AOC_40G Temp sensor will display on IPMI web gui 2. Category: Fix Description: [57601] System will record Vcpu Voltage incorrect event continually in IPMI Event Log. Infected motherboard: X10QBL Affected functions: Validation : 1. Check the SEL log, after running linpack test. ------------------------------------------------------------------------------------------ Filename: SMT_X10_173.bin version: 1.73 Date: 10-24-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57346] Fan mode does not change to optimal when GPUs are present Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. Power on the machine with GPUs installed 2. Check if PUE3 mode is hidden on IPMI fan mode web gui 3. Do fatctory default again and check step no.2 2. Description: R:[57529] VcpuVRM Temp reading is "N/A" in IPMI sensor reading page. Infected motherboard: X10SRA Affected functions: Validation : 1. Go to the Sensor list page of Webgui or issue the ipmitool sensor list command. 2. Check the VcpuVRM Temp reading. 3. Category: Enhancement Description: Support X10DDW-IN motherbaord Infected motherboard: X10DDW-IN Affected functions: Validation : 1. Use 0x30 0x21 command to get if the board id is "0x086E" ------------------------------------------------------------------------------------------ Filename: SMT_X10_172.bin version: 1.72 Date: 10-21-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Enhancement Description: [57161] Force fan mode to full when resetting/updating IPMI with GPUs Infected motherboard: X10DRG-H(T),X10DRG-Q,X10SRG-F,X10DRT-P(T)(IBF),X10DRU-i+ and X10DRU-X Affected functions: Validation : 1. When the BMC is not able to get the sensor readings (ex. BMC reset) with supported GPU/Intel Xeon Phi installed on the motherboard, fan speed goes to full speed (PWM = 100%) until BMC is able to get the sensor readings. 2. Above motherboards with no supported GPU/Intel Xeon Phi installed and other GPU motherboards follow default fan speed PWM duty cycle (PWM - 50%) when BMC is not able to get the sensor readings. 3. Setting fan PWM duty cycle to 50% after AC ON/OFF, i.e. AC power cord is unplugged (no standby power) and re-plugged in again. 2. Category: Fix Description: [57364] FAN PWM measurement fail for PCH Infected motherboard: X10QBL Affected functions: Validation : 1. Heat the PCH over 80 degree C. (Since CPU0 is nearby PCH, please take care not to heat CPU0 too much.) 2. Monitor the fan speed changing. 3. Category: Fix Description: [57366] FAN PWM measurement fail for CPU Infected motherboard: X10QBL Affected functions: Validation : 1. Heat the CPU over 70 degree C. 2. Monitor the fan speed changing. 4. Category: Fix Description: [57369] FAN PWM measurement fail for Memory. Infected motherboard: X10QBL Affected functions: Validation : 1. Heat one of the Memory to overheat. 2. Monitor the fan speed changing. 5. Category: Fix Description: [57370] The temperature of memory isn't correct. Infected motherboard: X10QBL Affected functions: Validation : 1. Heat one of the Memory to overheat. 2. Check the SEL log. 6. Category: Fix Description: [57355] Error sensor reading on AOM-STG-i2T. Infected motherboard: X10DRFF Affected functions: Validation : 1. Check sensor reading on AOM-STG-i2T. 7. Category: Fix Description: [57343] [Final Release] Multi-Node Power and Current Readings Are Wrong. Infected motherboard: X10DBT-T Affected functions: Validation : 1. Move the Multi Node page. 2. Check the Node Power and Current. 8. Category: Fix Description: [57346] Fan mode does not change to optimal when GPUs are present Infected motherboard: X10DRU-I+ Affected functions: Validation : 1. do reset-to-default and check the default fan mode on fan mode page. 9. Category: Enhancement Description: Per PM decision, changing NVMe sensors to "NVMe_SSD Temp." and renaming the wording "PCIeSSD" to "NVMe" on NVMe page. Infected motherboard: All Affected functions: Validation : check the sensor and NVMe pages. 10. Category: Fix Description: [57463] IPMI Memory sensor readings are incorrect. Infected motherboard: X10DRU-X(LL) Affected functions: Validation : 1. Move the sensor page. 2. Check the Memory sensor readings. 11. Category: Enhancement Description: Support Smart Cooling mode on fan mode page for specific CPUs. It will display when these CPUs are installed Supported CPU list : E5-2667 v3,E5-2643 v3,E5-2637 v3,E5-2623 v3 Also, the CPU fan curve is changed. Please follow the latest Thermal guide (T.B.D) When GPU is installed on certain motherboard, PUE2 and PUE3 mode will be hidden. Infected motherboard: Support Smart Cooling mode : X10DRU-I+, X10DDW-I, X10DRFF Support hidden PUE2 & PUE3 mode when installing GPUS: X10DRU-I+ Affected functions: fan mode function and CPU fan curve Validation : 1. Validate CPU fan curve when specific CPUs are installed 2. Make sure the smart cooling mode are default selected on the fan mode web gui 3. If you install GPUs on X10DRU-I+, the PUE2 & PUE3 mode will be hidden on fan mode web gui ------------------------------------------------------------------------------------------ Filename: SMT_X10_171.bin version: 1.71 Date: 10-14-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [57126] The setting mode of Fan isn't correct Infected motherboard: X10QBL Affected functions: Validation : 1. Check the default Fan mode in the web page. 2. Category: Fix Description: [57125] IPMI Hardware Monitor Check fail [56764] IPMI Monitor sensor readings are incorrect. Infected motherboard: X10QBL Affected functions: Validation : 1. Check the different value between reading value and measured value. 3. Category: Fix Description: [57127] Fan Pulse-Width-Modulation Measurement fail. [56985] CPU1~4 Temp/CPU4 VRM Temp will overheat and then system shutdown when system run full loading stress test. Infected motherboard: X10QBL Affected functions: Validation : 1. Login the Webgui and move to Fan mode page. 2. Change the fan mode. 4. Category: Fix Description: [57160] Fan mode not changed from PUE3 to Optimal when GPUs are present Infected motherboard: X10DRU-X, X10DRU-XLL Affected functions: Validation : 1. Check the default Fan mode in the web page. 5. Category: Fix Description: [56814] IPMI sensor can't readings any VRM Temp Infected motherboard: X10DRW-E,X10DRW-N Affected functions: Validation : 1. Check the memory VRM sensors on IPMI web gui 6. Category: Fix Description: [57177] It shows multiple "AOC_10G Temp" under IPMI webgui sensor reading page Infected motherboard: X10DDW Affected functions: Validation : 1. Check AOC_10G Temp on IPMI web gui 7. Category: Enhancement Description: [57014] [IPMI]In full speed mode, fan speed will drop when reset the BMC Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. For motherboard X10DRG-H(T), fan speed goes to full speed (PWM = 100%) after power on or BMC reset until BMC is able to get the sensor readings. After that, motherboard follows fan speed control curves when sensors start to poll 8. Category: Fix Description: [57289] No description about OS boot. Infected motherboard: All Affected functions: Validation : 1. Generate the SEL and Check the email. 9. Category: Fix Description: [57287] No deassertion - processor automatically throttled. Infected motherboard: All Affected functions: Validation : 1. Generate the Processor hot. 2. Check the Assertion SEL. 3. Cooling the Processor. 4. Check the Deassertion SEL. 10. Category: Fix Description: [57063] LED frequency measurement fail. Infected motherboard: X10QBL Affected functions: Validation : 1. Generate the power fail, fan fail and overheat events. 2. Check the OHLED behavior. 11. Category: Fix Description: [57319] System Fans go to FULL SPEED during system BIOS POST Infected motherboard: X10DDW Affected functions: Validation : 1. Do system power on, the fan duty cycle should be 50%, not 100% 12. Category: Fix Description: [57290] The hardware monitor test fail Infected motherboard: X10DRW-NT Affected functions: Validation : 1. Check if on board 10G sensor on IPMI sensor gui 13. Category: Fix Description: [57323] After update IPMI V1.70 FW, IPMI Network status is incorrect in Network Settings page [57277] Can't access IPMI WEB GUI with shared LAN after set IP address to Static [57227] Share LAN - Static IP isn't work [57189] Share Lan status doesn't display [57164] Network interface alway shows "dedicate" LAN mode in IPMI Web GUI Infected motherboard: All Affected functions: Validation : 1. Check if we can set status ip on IPMI network web gui 2. Check the dedicate and share mode on IPMI network web gui work fine 14. Category: Fix Description: [57269] Fan speed control error Infected motherboard: X10DRU+ Affected functions: Validation : 1. Set full speed on IPMI fan mode web gui 2. Check if the fan rpm is reached to maximum 15. Category: Fix Description: Cipher suite 0 from ADMIN to Unused. Infected motherboard: All Affected functions: Validation : 1. ipmitool -H -U ADMIN -P ADMIN lan print. 2. aaaaXXaaaXXaaXX -> XaaaXXaaaXXaaXX ------------------------------------------------------------------------------------------ Filename: SMT_X10_170.bin version: 1.70 Date: 10-03-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 ********** Please do factory default after this version is updated ********** 1. Category: Fix Description: [56764] IPMI Monitor sensor readings are incorrect. [56964] The voltage items doesn't show on IPMI. [56798] System will generate a lot of error event when run E-burn stress test. Infected motherboard: X10QBL Affected functions: Validation : 1. Login the WEBGUI 2. Check the sensor reading page. 2. Category: Fix Description: [56751] [BIOS 1.0a ECO] IPMI SLOTs report function(3a/5a) - FAILED Infected motherboard: X10QBI Affected functions: Validation : 1. Support riser 0x3a or 0x5a commands 3. Category: Enhancement Description: Implement new thermal guide 4.02 version (09092014) Implement PUE3 mode [56998] Fan PWM fail Infected motherboard: X10 motherboards Affected functions: Validation : 1. Test fan control function 4. Category: Fix Description: [56981] Fan ramps up due to wrong temperature reading Infected motherboard: X10DRU+ Affected functions: Validation : 1. Enter IPMI web page and check the vaule of RT2 sensor. It should not show "-1" 5. Category: Fix Description: [56921] IPMI hardware monitor fail Infected motherboard: X10DRD Affected functions: Validation : 1. Check IPMI sensor gui 6. Category: Fix Description: [57003] Function Fail, LAN temperature reading fail [56814] IPMI sensor can't readings any VRM Temp Infected motherboard: X10DRW-E Affected functions: Validation : 1. Check IPMI sensor gui 7. Category: New Feature Description: Enable FAN9 reading if users install a FAN device on RSC-W2-66 Infected motherboard: X10DRU_I_PLUS Affected functions: Validation : 8. Category: Enhancement Description: Support AMD FirePro S10000 GPU Infected motherboard: X10DRG-H(T),X10DRU,X10QBi and X10DRT-P Affected functions: Validation : 1. Install AMD FirePro S10000 GPU 2. Check GPU Temp being present 9. Category: Fix Description: [57042] IPMI should not have Dedicate option in Network Configuration. Infected motherboard: A1SRM-LN7F, A1SRM-LN5F Affected functions: Validation : 1. Check the Network Configuraion page 10. Category: Fix Description: [57039][57034][56244] SUM- Test case211 (Changebmccfg and compare.) failed Infected motherboard: C7Z97-MF X10DRU-X X10DRU-XLL Affected functions: Validation : 1. run SUM Test case 211. ---------------------------------------------------------------------------------------------- Filename: SMT_X10_169.bin version: 1.69 Date: 09-23-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r24 1. Category: Fix Description: [56428] Sometime when you are updating IPMI FW of both the nodes together the update progress will be stalled. Infected motherboard: X10DBT Affected functions: Validation : 1. Perform the IPMI FW update by WebGUI 2. Observe the update progress changing. 2. Category: Fix Description: [56400] Chassis Intrusion Events Logs During iKVM Stress Infected motherboard: X10DRC Affected functions: Validation : 1. Do iKVM stress test 2. Check the sel log about chassis intrusion. It should not happen again during the test 3. Category: Enhancement Description: Support second LSI infomation in web page Infected motherboard: All Affected functions: Validation : 1. Install 2 LSI cards in riser card(The maximum supported number of LSI device is 2) 2. Check LSI information in Storage Monitoring category after system boot into OS 4. Category: New Feature Description: Enable SNMP configuration and port setting functions in WEB. Infected motherboard: All Affected functions: Validation : 5. Category: Fix Description: [56633] Memory sensor readings shows abnormally. Infected motherboard: C7X99 Affected functions: Validation : 1. C7X99 does not support RDIMM. 2. Since UDIMM cannot support temperature reading, C7X99 would remove all memory temperature sensors. 6. Category: Fix Description: [56675] [Final Release]IPMI Email Alert Missing Event Description on Chassis Intrusion. Infected motherboard: All Affected functions: Validation : 1. Setup the setting of SMTP. 2. Generate the Chassis Intrusion Event. 3. Check the email. 7. Category: Fix Description: [56456] Logical Drive degraded event log in IPMI [55575] Got some false messages under SEL saying "Drive Fault @ slot2 /3 Infected motherboard: X10 Grantley platforms Affected functions: Disable LSI event log temporarily LSI event log functions (Use 0x30 0x70 0xfb 0x1 to enable event log function) Validation : 1. Do power on/off and check if any false alarm happen again. 8. Category: Fix Description: [55739] iKVM- The auto stop recording function is not working Infected motherboard: X10DRU-XLL Affected functions: Validation : 1. go to option->preference->display and enable auto stop. 2. go to record->start 3. when the timer expired,the ikvm will stop recording. 9. Category: Fix Description: [56674][Final_Release] IPMI Web Status Shown "Warning" While CPU Already OverHeat. Infected motherboard: Affected functions: Validation : 1. overheat CPU and check if the system health icon changes to "Critical " 10. Category: New feature Description: add PS consumption sensor Infected motherboard: X10DRT-P Affected functions: Validation : 1. check if there is PS consumption sensor on IPMI web.(please do reset-to-default) 11. Category: Fix Description: [56656] Function test issue -> C7Z97-M/C7Z97-MF OHLED test fail Infected motherboard: C7Z97-MF Affected functions: Validation : 1. Run SDHM 2. Check the Red LED. 12. Category: Enhancement Description: Enhance ATEN-IPMI-MIB and ipmi agent so that users are able to know what sensor names are. Infected motherboard: All Affected functions: Validation : 12. Category: Fix Description: [56761] Fan Optimal mode shoud be removed because that this board support single cooling mode only Infected motherboard: X10DRD Affected functions: Validation : 1.After updating the FW, please do factory default function 2.Check IPMI fan mode web gui 13. Category: Fix Description: [56671]How to identify temp sensors for AOC-S40G-i2Q & AOC-STG-i2T under IPMI sensor reading page Infected motherboard: All except motherboards with Denlow CPU Affected functions: Validation : 1. following the below name rule for LSI/NvME/10G/40 and please check IPMI sensor page.i PS: please do reset-to-default. MB/AOM_SAS Temp ==> onboard SAS MB_NVMe Temp ==> onboard NvME AOC_10G Temp ==> AOC 10G AOC_40G Temp ==> AOC 40G AOC_SAS Temp ==> AOC SAS AOC_NvME Temp ==> AOC NvME -------------------------------------------------------------------------------------------- Filename: SMT_X10_168.bin version: 1.68 Date: 09-15-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 1. Category: Fix Description: [56474] ACPI Status still show "Host is currently off" in IPMI Power Control and Status page after system power cycle. Infected motherboard: All Affected functions: Validation : 1. Login the webgui and switch to Power control page 2. Select "Power Cycle" and press "Perform Action". 2. Category: Customer Requirement Description: 0x30 0x70 0x72 command to set watch dog by seconds for A1SRM_LN7F Infected motherboard: A1SRM_LN7F Affected functions: Validation : 1. Set watchdog command to trigger after 300 seconds. ipmicfg -raw 30 70 72 1 1 2c 1 2. Count 300 seconds and see if the system do reset -------------------------------------------------------------------------------------------- Filename: SMT_X10_167.bin version: 1.67 Date: 09-12-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 1. Category: Fix Description: [56368] [IPMI 1.64 ECO] SMTP Setting error messages keeps popping up after entering incorrect values. Infected motherboard: All Affected functions: Validation : 1. Login the webgui and switch to SMTP page. 2. Try the error case of SMTP setting. 2. Category: Enhancement Description: Show "Max Capable Speed" and "Operating Speed" in DIMM category (Hardware Information web page) [56260] [IPMI 1.63] IPMI hardware information memory speed does not meet the BIOS settings Infected motherboard: All Affected functions: Validation : 1. Max Capable Speed: SMBIOS Memory Device (Type 17) offset 15h The maximum capablespeed of the device. 2. Operating Speed: SMBIOS Memory Device (Type 17) offset 20h The configured clock speed to the memory device 3. Category: Fix Description: [56393] Upload BIOS fail through IPMI Infected motherboard: A1SRM-LN7F family Affected functions: Validation : 1. Login the webgui. 2. Update the BIOS. 4. Category: Fix Description: [56393] Upload BIOS fail through IPMI Infected motherboard: A1SRM-LN7F family Affected functions: Validation : 1. Login the webgui. 2. Update the BIOS. 5. Category: Fix Description: [56456] Logical Drive degraded event log in IPMI [55575] Got some false messages under SEL saying "Drive Fault @ slot2 /3 Infected motherboard: X10 Grantley platforms Affected functions: Disable LSI event log temporarily LSI event log functions (Use 0x30 0x70 0xfb 0x1 to enable event log function) Validation : 1. Do power on/off and check if any false alarm happen again. 6. Category: Fix Description: [56377] Vendor ID under PCIe SSD monitoring tab is in wrong order Infected motherboard: X10 Grantley platforms with Intel NvMe devices Affected functions: Validation : 1. Enter NvMe web page 2. Check the vendor id of Intel SSD is "80 86" 7. Category: Enhancement Description: Support AOC Temp for AOC-S40G-i2Q Infected motherboard: All except motherboards with Denlow CPU Affected functions: Validation : 1. Install AOC-S40G-i2Q 2. Check if AOC Temp is present in sensor list 8. Category: Fix Description: [56385] No 10G AOC temperature reading in IPMI Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. Update X10DRG4.908 BIOS 2. Check if AOC Temp is present in sensor list when AOC card is installed 9. Category: Add Motherboard Description: Add new motherboard configuration - X10DRW_E,X10DRD Infected motherboard: Affected functions: Validation : 10. Category: Workaround Description: Add ME Reset function if the ME is in abnormal state. Infected motherboard: X10QBi Affected functions: Validation : 11. Category: Fix Description: Fans are running at full speed even system is sitting idle at PXE screen Infected motherboard: X10DDW, X10DDW_I3 Affected functions: Validation : 1. Do S4 stress test 2. When system is powered off, the fan speed is at full speed 3. Select "Power On" function on IPMI web gui 3. Check if the fan speed is back to normal -------------------------------------------------------------------------------------------- Filename: SMT_X10_166.bin version: 1.66 Date: 09-09-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 1. Category: Fix Description: [56340] GPU Numbering in IPMI Does Not Follow GPU Thermal Guideline Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. The GPU label will be GPU3/GPU4 in slot 4 for 2U 6 GPU 2. The GPU label will be GPU5/GPU6 in slot 1 for 2U 6 GPU 2. Category: Enhancement Description: Support Nvidia M40 GPU Infected motherboard: X10DRG-H(T),X10DRU,X10QBi and X10DRT-P Affected functions: Validation : 1. Install Nvidia M40 GPU 2. Check GPU Temp being present 3. Category: Fix Description: [56401] Agent managed command-Reset chassis intrusion failed Infected motherboard: X10 motherboards with ast2400 internal superio Affected functions: Validation : 1. Short JL1 pin to let chassis case open 2. Enter dos mode and key-in "ipmicfg -raw 30 3" 3. It should not have error message appear "IPMI command not completed normally, Completion Code=FFh" -------------------------------------------------------------------------------------------- Filename: SMT_X10_165.bin version: 1.65 Date: 09-05-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 1. Category: Fix Description: [56320] OH LED comes up everytime for 20 seconds while doing windows S4 stress test [56294] Got lots of CPU1 & CPU2 "Processor Automatically Throttled" messages under IPMI SE Infected motherboard: X10 Grantley platforms Affected functions: Validation : 1. Do the S4 stress test 2. BMC should not have cpu prossor hot event log 3. Buzzer should not beep 4. Overheat Led should not be flashing 2. Category: Fix Description: [56339] CPU overheat audible and alert LED stays on even after CPUs are cooled down Infected motherboard: X10DRU Affected functions: Validation : 1. Overheat CPU and let overheat LED turns on and the buzzer beeps. 2. cooldown the CPU temperature 3. Check if Overheat LED turns off and buzzer stop beeping 3. Category: Fix Description: [56117] iKVM Reset function is fail Infected motherboard: All Affected functions: Validation : 1. Do the iKVM reset function. 2. Virtual media should not exist 3. Check if Overheat LED turns off and buzzer stop beeping 4. Category: Fix Description: [56157] [NVME injection btn] IPMI Web GUI information not updated during hot plug test. System need to reboot in order to bring up updated info Infected motherboard: X10 Grantley motherboard with CPLD NvME backplane Affected functions: Validation : 1. Do the eject button 2. NVMe SSD information should not show after hot remove the drive 5. Category: Fix Description: [56402] [Final Release Package] REOPEN ISSUES(PBID#56193, 56257, 56225, 56126) that happens on v1.65 again. Infected motherboard: All Affected functions: Validation : 1. Generate the SEL. 2. Check the mail and SEL. -------------------------------------------------------------------------------------------- Filename: SMT_X10_164.bin version: 1.64 Date: 09-03-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 *****************Please do factory deafault after burning this FW**************** 1. Category: Fix Description: [56257] 1.63]Email EVENT_DIRECTION show "De-assertio" when event deasserted [56252] Email EVENT DIRECTION show "De-assertion" when event deasserted. Infected motherboard: All Affected functions: Validation : 1. De-assert the event. 2. Check the Email. 2. Category: Fix Description: [56259] [ SUM 1.4.0 ] IPMI is not active but sum checkoobsupport isn't. Infected motherboard: All Affected functions: Validation : 1. Check the result of SUM checkoob support. 3. Category: Enhancement Description: [56091] [ SUM 1.4.0 ] Random - Soft shutdown is not work Infected motherboard: All Affected functions: Validation : 1. Please do software power shutdown fucntion on IPMI web gui to see if it works at Redhat system 4. Category: Fix Description: [56097] [2U-SYS] Xeon-Phi Lost After Running Cburn ONOFF 153 Cycles Infected motherboard: X10DRT-P Affected functions: Validation : 1. Check if BMC finds GPU sensors 4. Category: Fix Description: [55667] Got some messages about AOM3108 controller under SEL [55604] "Drive Fault" during ONOFF test on X10DRC-LN4+ [55575] Got some false messages under SEL saying "Drive Fault @ Infected motherboard: X10 Grantley platforms Affected functions: Disable LSI event log temporarily LSI event log functions Use 0x30 0x70 0xfb 0x1 to enable event log function Validation : 1. Do power on/off and check if any false alarm happen. -------------------------------------------------------------------------------------------- Filename: SMT_X10_163.bin version: 1.63 Date: 08-29-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 1. Category: Fixed Description: [56206] BIOS can't update from IPMI WebGUI [56178] Can't update BIOS with IPMI Web GUI [56177] BIOS OOB update from IPMI webgui failed on IPMI FW 1-62 version [56163] [Final Release] IPMI v1.62 BIOS update Fail under Web GUI [56160] Cannot activate product key through SUM ./activate.sh [56112] Flash BIOS via IPMI web is fail Infected motherboard: All motherboards Affected functions: Validation : 1. Login WebGui 2. Update BIOS. 2. Category: Enhancement Description: Set/Get System Info Parameter command Infected motherboard: Affected functions: Requirement : 1. Please use TAS v1.0.1 and SUM v1.4.1 to work together. 3. Category: Fix Description: [56194] [Final Release] IPMI v1.61 - Email Alert Missing Event Description For "Processor Automatically Throttled" [56126] No description for the Processor Automatically Throttled email alert event. Infected motherboard: All Affected functions: Validation : 1. Setup the SMTP configuration. 2. Trigger Processor Automatically Throttled event. 3. Check the email. 4. Category: Fix Description: [55725] IPMI failed to detect more than 3 GPU temp Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. Install riser card RSC-G2FR-A66 in slot4 2. Check GPU5/GPU6 is present correctly when GPU exists 5. Category: Fix Description: [56140] The email alert shows "OS Critical Stop" when the system is Graceful Shutdown. Infected motherboard: All Affected functions: Validation : 1. Setup the SMTP configuration. 2. Graceful shutdown the system. 3. Check the email. 6. Category: Fix Description: [56193] [Firmware v1.62 Final Release Package] Event Log description incorrect in IPMIWeb GUI. Infected motherboard: All Affected functions: Validation : 1. Setup the SMTP configuration 2. Trigger the threshold event. 3. Check the email. 7. Category: Fix Description: [56193] Drive fault error while running HD stress test [55837] LSI temperature will randomly disappear [55604] "Drive Fault" during ONOFF test on X10DRC-LN4+ [55575] Got some false messages under SEL saying "Drive Fault @ slot2 /3" Infected motherboard: X10 Grantley platform Affected functions: Validation : 1. Install the SAS HDD and create Raid. Clear all the event log message 2. Do cburn on/off test 3. Check if any false alarm happen 8. Category: Fix Description: [56162] [IPMI] AOM Module got OH after IPMI reset Infected motherboard: X10DDW Affected functions: Validation : 1. When bmc do coldrboot or sytem is powered on or reset 2. Check the fan speed is near 100% duty cycle 9. Category: Fix Description: [56162] [SUM 1.4]Test case 235 "Clear event log" failed Infected motherboard: X10DRI-T Affected functions: Validation : 1. First, update BMC firmware 2. Update bios x10dri14.826 3. Check [SUM 1.4]Test case 235 ================================================================================================== Filename: SMT_X10_162.bin version: 1.62 Date: 08-26-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 ********************************* X10DRT-P Release Only********************************** 1. Category: Enhancement Description: [55962] CPU temp stays at 40C even when stressed at 4.6ghz [55899] CPU Overheat Buzzer Function does Not Work Infected motherboard: C7Z97_M, X10SRA Affected functions: Validation : 1. Stress test and check the cpu temperature 2. make CPU overheat and listen if the buzzer start working 2. Category: Fix Description: [56081] LSI 3108 temperature gone after doing IPMI factory default Infected motherboard: X10 Grantley platforms Affected functions: Validation : 1. Wait and you can see LSI temperature appear on the IPMI sensor reading page 2. Do factory default 3. Enter the IPMI web gui again and refresh to see if LSI temperature value is gone 3. Category: Fix Description: [LSI] Disable LSI event log temporarily Infected motherboard: X10 Grantley platforms Affected functions: LSI event log functions Use 0x30 0x70 0xfb 0x1 to enable event log function Validation : 1. Do power on/off and check if any false alarm happen. ================================================================================================== Filename: SMT_X10_161.bin version: 1.61 Date: 08-XX-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r23 1. Category: Enhancement Description: Support Nvidia M3-3020 GPU Infected motherboard: X10DRG-H(T),X10DRU,X10QBi Affected functions: Validation : 1. Install Nvidia M3-3020 GPU 2. Check GPU Temp being present 2. Category: Fix Description: [55856] IPMI only shows two GPU temperatures Infected motherboard: X10DRU Affected functions: Validation : 1. Check GPU2 Temp/GPU3 Temp being present if GPU exist 3. Category: Enhancement Description: Get NvME information from CPLD (No support old NvME protocol now) Infected motherboard: First support on X10DBT, X10DRU, X10DRT_P and X10DDW. Other X10 Grantley motherboards need to be regarbered. Need new backplane support. Affected functions: Validation : 1. Check NvMe function 4. Category: Fix Description: [55894] Memory Temp readings are incorrect Infected motherboard: X10DRU Affected functions: Validation : 1. Heat speicfic Memory. 2. See the temperature value are rising or not. 5. Category: Fix Description: [55678] 'LAN Temp' is shown 'Upper Critical' after upgrading IPMI FW to v1.58 Infected motherboard: X10DRH-I Affected functions: Validation : 1. Make sure X10DRH-I has no any LAN Temp sensor. 6. Category: Fix Description: [55584] Sometimes some virtual keyboard color is black Infected motherboard: Affected functions: Java viewer Validation : 1. Check if some virtual keyboard color is black sometimes 7. Category: New platform Description: Support new motherboard: X10QBL Infected motherboard: X10QBL 8. Category: Fix Description: [ SUM 1.4.0 ] Change BMC configuration is fail. Infected motherboard: All Affected functions: Validation : 1. run the test case 211 9. Category: Fix Description: [55886] 10G LAN Temperature and Fan Speed Unstable with System Idle Infected motherboard: X10DRH-CT Affected functions: Validation : 1. Make the system in idle. 2. Observe the Zone2 fan speed(FanA, FanB) and Zone2 sensors(PCH, LAN, Peripheral, LSI). ================================================================================================== Filename: SMT_X10_160.bin version: 1.60 Date: 08-19-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [55739] iKVM- The auto stop recording function is not working Infected motherboard: X10DRU-XLL Affected functions: Validation : 1. go to option->preference->display and enable auto stop. 2. go to record->start 3. when the timer expired,the ikvm will stop recording. 2. Category: Fix Description: [ SUM 1.4.0 ] Change BMC configuration is fail. Infected motherboard: X10SRL-F Affected functions: Validation : 1. run the test case 211 3. Category: Enhancement Description: Trigger CPU overheat by PROCHOT_N according to Thermal Guide Rev 4.02 Infected motherboard: X10DP Motherboards Affected functions: Validation : 1. Wait the PROCHOT_N has falling edge, the SEL would be generated. ================================================================================================== Filename: SMT_X10_159.bin version: 1.59 Date: 08-14-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [55642] Wrong GPU temperature readings in SEL [55645] IPMI SEL gets Xeon Phi Temp going high when running onoff test [55684] [IPMI] Got GPU OH event when runing linpack on CPU but NO loading on GPUs Infected motherboard: X10DRG-H(T),X10DRU-i+,X10DRU-X,X10DRU-XLL Affected functions: Validation : 1. Check no IPMI SEL of Xeon Phi Temp/GPU Temp going high when running onoff test 2. Category: Fix Description: [55507] BMC reset fails, drops IPMI Infected motherboard: X10DRU Affected functions: Validation : 1. do BMC cold reset stress test 3. Category: Fix Description: [55652] IPMI FW 1.58 does not even show "LSICtl1 Temp" under sensor reading page Infected motherboard: X10DRU Affected functions: Validation : 1.Need bios to send 0x3a and 0x5 commands 2.Check if LSICtrl sensor value exists. If not, it means bios does not send them yet 4. Category: Fix Description: [55589] UID need to support or not? Infected motherboard: C7Z97-M Affected functions: Validation : 1.Remove UID function 5. Category: Fix Description: R: [55694]The privilege settings for User and Operator are incorrect. Infected motherboard: X10DRU Affected functions: Validation : 1.login as the operateri or user privilege 2.check if the user is able to have full or view access on ipmi web pages, like ldap,ddns and so on. 6. Category: Fix Description: [55700] IPMI Summary page showed additional LAN device(LAN 7) Infected motherboard: All Affected functions: Validation : 1. See the main page of WebGUI. 7. Category: Fix Description: [55661] [BETA RELEASE] CPU and MEM Temperature Sensor Lost with IPMI FW to 1.58 Infected motherboard: X10DBT Affected functions: Validation : 1. Run Cburn Test. 2. Monitor the Sensor Reading page. 8. Category: Fix Description: [55533] Fan PWM of memory is fail Infected motherboard: A1SRM-LN7F Affected functions: Validation : 1. Heat the Memory. 2. Check the Fan Speed. 9. Category: Fix Description: [55712] R2 cpu stepping cause IPMI memory temperture sensor reading wrong detect [55689] IPMI sensor reading detect wrong memory slot temperture Infected motherboard: X10DRFR, X10DRFF Affected functions: Validation : 1. plug P1-DIMMA1, P1-DIMME1. check if other dimm sensor has duplicate values 10. Category: Fix Description: [55667] Got some messages about AOM3108 controller under SEL Infected motherboard: X10DDW Affected functions: Validation : 1. Check if LSI LNC, LC, LNR event log of LSI control sensor will be sent ----------------------------------------------------------------------------------------------------------- Filename: SMT_X10_158.bin version: 1.58 Date: 08-11-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [55613] IPMI CPU sensor readings disappear when CPU overheats. Infected motherboard: X10DBT-P Affected functions: Validation : 1. Heat the CPU to overheat. 2. Monitor the sensor reading. 2. Category: Fix Description: [55577] System runs at 70% to 80% of fan speed with AOM-3108 temp reaches to 75C while sitting idle in room temperature Infected motherboard: X10DDW Affected functions: Validation : 1. Heat the monitoered sensor to overheat 2. Monitor the fan curve of PUE-optimal mode 3. Category: Fix Description: [55599] Fan sensor status indictor incorrect while FAN-Failure. Infected motherboard: All Affected functions: Validation : 1. Remove a FAN. 2. See the color of fan in the sensor reading page of WebGUI. ----------------------------------------------------------------------------------------------------------- Filename: SMT_X10_157.bin version: 1.57 Date: 08-08-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [55560] [BIOS] Fail To Flash BIOS Under DOS Infected motherboard: X10DBT-P, X10QBI Affected functions: Validation : 1. Please flash bios under the dos 2. Category: Fix Description: [55500] I lost PCie_SSD tab & also lost PCIeSSD temp from sensor reading whenever I try to remove HDD connected to AOC 3108 [55466] PCIe SSD tab NVMe temp & sensor reading PCIe SSD temp do not match [54886] IPMI webgui does not show correct NVMe SSD temp under PCIe_SSD tab Infected motherboard: X10DDW Affected functions: Validation : 1. Check NvMe sensor 3. Category: Fix Description: [55238] [SDIII] Some voltage values weren't in limit [55062] Some SDIII sensor reading is incorrect Infected motherboard: C7Z97_M, X10SRE-DS018 Affected functions: Validation : 1. Check NvMe sensor 4. Category: Fix Description: [55016] CPU fan speed control not correct under both PUE and Optimial Mode Infected motherboard: X10DRU-i+,X10DRU-X,X10DRU-XLL Affected functions: Validation : 1. Heat CPU1 or CPU2 2. Check fan control is working properly per region ----------------------------------------------------------------------------------------------------------- Filename: SMT_X10_156.bin version: 1.56 Date: 08-06-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [55232] [EVT] "PCH Tempe" displays "Not Present" in IPMIWeb GUI with firmware v1.54 [55229] [EVT] Sensors of Onboard "10G LAN Temperature" displays "Not Present" in IPMIWeb GUI with firmware v1.54 Infected motherboard: X10DRH Affected functions: Validation : 1. Check the sensor reading of PCH and LAN Temp 2. Category: Fix Description: [55392] [EVT] There is no FAN PWM for AOM3108 controller Infected motherboard: X10DDW Affected functions: Validation : 1. Heat LSI temperature sensor, and check if fan rpm is rising 3. Category: Fix Description: [55244] BIOS Resilience" is not working in firmware v1.54. Infected motherboard: X10DRG-Q Affected functions: Validation : 1. Check the WebGUI. 4. Category: Fix Description: [55426] IPMI CPU status conflicting with threshold definition Infected motherboard: X10DRU-I+ Affected functions: Validation : 1.IPMI Follow the latest thermal guide SIM_TDG REV. 4.02 (07XX2014).pdf 2.Non-recoverable and Critical thresholds show red color 3.Only critical event log is required 5. Category: Fix Description: [55272] PCI-e SSD tab is missing when you do factory default in IPMI Infected motherboard: X10DRU-I+ Affected functions: Validation : 1.Do factory default action 2.Do not login in the IPMI web gui too quickly because BMC loads the riser configuration and then add dynamic sensors. 3.Login in the web gui to check if PCIe SSD tab is not missing 6. Category: Fix Description: [55242] No GPU sensor reading in IPMI Webgui. Infected motherboard: X10DRG-Q Affected functions: Validation : 1.Check IPMI sensor page.(need newer bios to set 0x3a/0x5a command) 7. Category: Fix Description: [55397] FAN 2, FAN 5 reading issue. Infected motherboard: X10DRG-Q Affected functions: Validation : 1.Plug FAN5 and check IPMI sensor page to get FAN5's reading. 2.Plug FAN2 and FAN5, then unplug FAN5. Check IPMI sensor page 3.Plug FAN2 and FAN4, then unplug FAN2. Check IPMI sensor page 8. Category: Fix Description: [55368] PUE fan mode should be removed and Optimal fan mode should be the default fan speed control Infected motherboard: X10DRU-I+ Affected functions: Validation : 1.Do factory default after update the latest IPMI FW 2.Check the fan mode web page(default Optimal mode) 3.PUE mode won't be removed 4.Check PUE mode do fan control per region 9. Category: Fix Description: [54230] [ SUM 1.3.0 ] Change BMC configuration fail. [54229] [ SUM 1.3.0 ] Change BMC configuration fail. Infected motherboard: X10DRW-IT, X10SRL Affected functions: Validation : 1. SUM test 10. Category: Fix Description: [54999] The temperature of memory is fail Infected motherboard: A1SRM-LN7F Affected functions: Validation : 1. Check the sensor reading of Memory sensors. 11. Category: Enhancement Description: Go full speed when boot or bmc reset Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. FANs go full speed in 10 seconds after power on or BMC reset. FAN speed will get recovery when sensors start to poll. 12. Category: Fix Description: [55399][55398]IPMI_iLO test fail for VMware ESXi 5.5 Cert Infected motherboard: X10DRFF,X10DRW Affected functions: Validation : 1. run Vsphere client to setting IPMI/iLO on vCenter5.5 and see if it is ok 13. Category: Fix Description: [55453] Unable to read GPU temperature on IPMI 1.54 Infected motherboard: X10DRU-X(LL) Affected functions: Validation : 1. Check the sensor reading of GPU. ----------------------------------------------------------------------------------------------------------- Filename: SMT_X10_155.bin version: 1.55 Date: 07-30-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [55272] PCI-e SSD tab is missing when you do factory default in IPMI Infected motherboard: X10DRU-+ Affected functions: Validation : 1. Do factory default action, then check if PCI-e SSD tab still exists 2. Category: Fix Description: [55266] Fan7 / Fan 8 are not working Infected motherboard: X10DRU-+ Affected functions: Validation : 1. Check IPMI sensor page 3. Category: Fix Description: [55236] PCIe_SSD tab is missing from IPMI webgui & PCIe_SSDsensor reading missing from sensor reading [54935] PCIeSSD temp sensor reading lost from sensor reading page [54886] IPMI webgui does not show correct NVMe SSD temp under PCIe_SSD tab Infected motherboard: X10DRU-+, X10DDW Affected functions: Validation : 1. Check IPMI sensor page. (Need bios to pass command to tell IPMI the NvME card exist) 4. Category: Fix Description: [55227] IPMI FW 1.54 Shows Two Temperature Sensors for Onboard LSI Controller Infected motherboard: X10DRC Affected functions: Validation : 1. Check IPMI web gui (need newer bios to set 0x3a/0x5a command to activate on board LSI) 5. Category: Fix Description: [55140] Fan naming not matches with onboard Fan silkscreen [#54675 reopen] Infected motherboard: X10DRU-XLL Affected functions: Validation : 1. Check the fan name and anothre on the silkscreen 6. Category: Fix Description: [54986] CPU Overeheat Events Do Not Log with PROCHOT Assertion Infected motherboard: X10DRI, X10DRC Affected functions: Validation : 1. Check the thermal guide Rev. 4.02 2. COA is activated when PROCHOT_N signal is asserted System monitor sw is requirement to report and record CPU overheating events in event logs 3. COA is de-activated when CPU is cooled down from PROCHOT_N and DTS reading is equal to or smaller than -2 7. Category: Fix Description: [54642] FAN C&D will not speed up when I set to "Full Speed" Fan mode Infected motherboard: X10SRG Affected functions: Validation : 1. Check the IPMI web gui -------------------------------------------------------------- Filename: SMT_X10_154.bin version: 1.54 Date: 07-28-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 ***** For product spec. supports smbus mux design/riser card/AOC sensor reading ***** ***** /GPU sensor reading on Grantley platform, IPMI needs newer bios to support ***** ***** NetFn=0x30 Cmd=0x70 SubCmd=0x3a and 0x5a command ***** 1. Category: New feature Description: Support 8 riser cards. AOC-UR-i2XT,AOC-UR-i4XT,AOC-2UR6-i4XT,AOC-UR-i4G,AOC-2UR68-i4G,AOC-UR-i4G RSC-R2UW-4E8, RSC-R1UW-2E16,RSC-R2UW-2E8E16,RSC-R1UW-E8R, AOC-2UR68-i2XT,RSC-R1UG-A2E16-X9,RSC-R1UG-E16-X9, RSC-R1UG-E16AR+II,RSC-R1UG-2E8AR+II,RSC-R1UG-E16R+II, RSC-G2F-A66,RSC-G2FR-A66,RSC-G2B-A66 Need new bios to send 0x3a, 0x5a command to activate GPU, Arp 10G AOC, LSI AOC/AOM, and NvME. after IPMI 1.54, BMC will NO LONGER detect above devices by itself on X10 Grantley platform. Infected motherboard: X10 Grantely motherboards Affected functions: GPU cards, Arp 10G AOC, LSI AOC/AOM, NvME Validation : 1. Check if BMC can show these sensors of GPU, Arp 10G AOC, LSI AOC/AOM, NvME 2. Category: Fix Description: [55159] System has lost all sensor readings from IPMI webgui Infected motherboard: X10DDW Affected functions: Validation : 1. Do factory default 3. Category: Fix Description: [55158] [EVT] Fan mode not works at all Infected motherboard: X10DRH Affected functions: Validation : 1. Check fan mode 4. Category: Fix Description: [55157] [EVT] Non Sensor was displayed in firmware v1.53 Infected motherboard: X10DRH Affected functions: Validation : 1. Check fan mode 5. Category: Fix Description: [55079] SD5 shows FAN1 in "red color" even though it is not connected Infected motherboard: X10DDW Affected functions: Validation : 1. Check senors and SD5 6. Category: Fix Description: [55050] Number of Fans in IPMI wengui sensor reading page do not match with physical fan headers on motherboard Infected motherboard: X10DDW Affected functions: Validation : 1. Check all fans are working when fans are fully populated. 7. Category: Fix Description: [55036] No RT1/system sensor reading on IPMIGUI Infected motherboard: X10DRU-i+, X10DRU-X, X10DRU-XLL Affected functions: Validation : 1. Check IPMI web gui 8. Category: Fix Description: [54984] FW 1.53 Logs Upper Non-Recoverable Events Infected motherboard: X10 Grantley motherboards Affected functions: Validation : 1. Heat the cpu to overheat state. Check no no-recoverable events occurs 9. Category: Fix Description: [54935] PCIeSSD temp sensor reading lost from sensor reading page Infected X10DDW Affected functions: Validation : 1. Check if NvME Temp sensor is sometimes gone when NvME device is detected 10. Category: Fix Description: [54935] PCIeSSD temp sensor reading lost from sensor reading page [54886] IPMI webgui does not show correct NVMe SSD temp under PCIe_SSD tab Infected X10DDW Affected functions: Validation : 1. Check if NvME Temp sensor is sometimes gone when NvME device is detected 2. Check PCIe_SSD tab shows correct information 11. Category: Fix Description: [54764] No LAN temperature readings in IPMI web GUI Infected motherboard: X10DRU-i+ Affected functions: Validation : 1. Insert AOC-XX-card to check bmc can read X540 LAN sensor (need newer bios) 12. Category: Fix Description: [54388] No NVMe drive Location Menu in IPMI Web GUI Infected motherboard: X10DRU-I Affected functions: Validation : 1. Insert AOC-XX-card to check bmc can read NvME device (need newer bios) 14. Category: Fix Description: [54069] [IPMI] IPMI web doesn't show correct GPU label Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. Please refer GPU_info.xlsx to determine GPU label and supported GPU number 15. Category: Fix Description: [55232] PCH Tempe" displays "Not Present" in IPMIWeb GUI with firmware v1.54 [55229] Sensors of Onboard "10G LAN Temperature" displays "Not Present" in IPMIWeb GUI with firmware v1.54 Infected motherboard: X10DRH Affected functions: Validation : 1. Check IPMI web page -------------------------------------------------------------- Filename: SMT_X10_153.bin version: 1.53 Date: 07-xx-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [54675][EVT] Fan naming not matches with onboard Fan silkscreen Infected motherboard: X10DRU-i+, X10DRU-X, X10DRU-XLL Affected functions: Validation : 1. Check the fan5~8 sensor names. 2. Category: Fix Description: [54761]No standard mode function in IPMI Infected motherboard: X10DRU-X, X10DRU-XLL Affected functions: Validation : 1. Check the fan mode configuration page of WebGUI. 3. Category: Enhancement Description: Nvidia new GPU card(K80) support Infected motherboard: x10 all platform Affected functions: Validation : 1. When K80 is installed, check GPU Temp on sensor page. 4. Category: Enhancement Description: [54840][EVT] LAN Temperature shows "not present" Infected motherboard: X10DRU-X, X10DRU-XLL, X10DRU-i+ Affected functions: Validation : 1. Check the LAN Temp sesnor on the sensor page. 5. Category: Enhancement Description: [54867][IPMI] IPMI drop XeonPhi #3 temperature reading and fan speed is set to 1500 RPM during overnight cburn on/off test. Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. Check if XeonPhi #3 temperature reading is gone during overnight cburn on/off test. 6. Category: Fix Description: [54817] CPU Overheat LED is not working when CPU overheat Infected motherboard: C7Z97-MF Affected functions: Validation : 1. Overheat the cpu and observe if the led is solided on. 7. Category: Fix Description: [54812] FAN Failure LED is not working when FAN fail Infected motherboard: C7Z97-MF Affected functions: Validation : 1. pull out the plugged fan and obseve if the led is flashing 8. Category: Fix Description: [54812] Drive Not Present in IPMI SEL with AOM-3108 Infected motherboard: X10DRW-I Affected functions: Validation : 1. On/Off stress test on the motherboard with LSI HDDs installed 2. Check the false alarm event happen. 9. Category: New motherboards Description: C7X99_OCE, X10SRA-F Infected motherboard: C7X99_OCE, X10SRA-F Affected functions: Validation : -------------------------------------------------------------- Filename: SMT_X10_152.bin version: 1.52 Date: 07-11-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 ***X10DRT-P, X10DRC Production Release*** 1. Category: Fix Description: [54373] PCIe SSD sensor readings are wrong under IPMI webgui sensor page [54372] IPMI sensor reading webpage only shows 3 PCIe SSD temp, it should be 4 as I have 4 ports on mb Infected motherboard: X10DDW Affected functions: Validation : 1. Connect the PCIe NvME SSDs 2. Check if PCIeSSD web page appears and content are right 3. Check if only one PCIeSSD temperature sensor on sensor reading pages 2. Category: Fix Description: [54264] 5VCC low on node2 when running cburn Infected motherboard: A1SA2 1.02 motherboards Affected functions: Validation : 1. Do cburn on/off on both node 2. Check if 5VCC sensor sel log on node2 will appear. 3. Category: Fix Description: [54217] IPMI SEL (event log) got some unknown "Chassis Intrusion" messages Infected motherboard: X10DRi Affected functions: Validation : 1. Run system S4 stress test 2. Check SEL logs 4. Category: Fix Description: [54561] RT2 Temperature in IPMI is Higher than Measured Thermocouple Value Infected motherboard: X10DRC Affected functions: Validation : 1. Check the RT2 temperature of this version is lower 9 degree from ther preious IPMI version 5. Category: Fix Description: [54556] LAN temperature in IPMI web shows as 9x degree C when system idle Infected motherboard: X10DRG-Q Affected functions: Validation : 1. Check if no LAN sensor again on the IPMI sensor reading page 2. If yes, do factory default 6. Category: New Feature Description: The sensor reading of A1SRM_LN7F, X10DRU_X, C7Z97_M are supported Infected motherboard: A1SRM_LN7F, X10DRU_X, C7Z97_M Affected functions: Validation : 1. Check on IPMI sensor reading page 7. Category: Fix Description: [54642] FAN C&D will not speed up when I set to "Full Speed" Fan mode. Infected motherboard: X10SRG Affected functions: Validation : 1. Check on fan mode if works 8. Category: Fix Description: [54606] Fan control function didn't work on Fan A, B, C and D Infected motherboard: X10SDRG-Q Affected functions: Validation : 1. Check on fan mode if works 9. Category: Fix Description: [54552] [SYS-5038MA-H24TRF] No power supply column in sensor reading page. Infected motherboard: A1SA2, X10SLE-D,X10SLE,X10SLD Affected functions: Validation : 1. Check if power sensor exists on IPMI sensor reading page 10. Category: Fix Description: [54574] There is no chassis intrusion sensor reading on IPMI WebGUI Infected motherboard: X10DRU-X Affected functions: Validation : 1. Check the Sensor list. 11. Category: Fix Description: [53518] [IPMIView] Trap Shows Incorrect Sensor Name for All DIMM Slots with Memory ECC Assertion Infected motherboard: X10DRC Affected functions: Validation : 1. Setup the IPMI smtp setting 2. Launch the Trap Receiver on IPMIView 3. Trigger Memory ECC command to check. The sensor name should show "DIMMA1", not "DIMM1A". 12. Category: Fix Description: [54532] Everytime I try to locate different NVMe SSDs (0,1,2,3) under PCIe SSD tab but it always locate slot 0 Infected motherboard: X10DRC Affected functions: Validation : 1. Enter PCIe web page 2. Set locate function to other slot. Do not set to slot 0 3. Check if the function works. 13. Category: Fix Description: [54326] System goes to full fan speed mode whenever I go to cburn. Infected motherboard: X10QBi Affected functions: Validation : 1. Run the Cburn on/off test. 2. Check the fan speed is normal or not. 14. Category: Enhancement Description: Remove duplicate systm info page. Infected motherboard: X10QBi Affected functions: Validation : 1. Since System page and System info page show the same information. Just remove it 15. Category: Enhancement Description: Remove duplicate systm info page. Infected motherboard: X10 all platforms Affected functions: Validation : 1. Since System page and System info page show the same information. Just remove it 16. Category: Enhancement Description: Add Hardware information page on System tab Infected motherboard: X10 all platforms Affected functions: Validation : 1.Bios needs to send smbios information to bios 2.Then IPMI web page will present this information 17. Category: Fix Description: [54607] Some fan speed sensor readings didn't match silkscreen Infected motherboard: X10DRG-Q Affected functions: Validation : 1.Check if fan number names are the same as another printed on the silkscreen 18. Category: Fix Description: [51386] IPMI cannot handle network looping (ARP packet storm) Infected motherboard: X10DRT-P Affected functions: Validation : 1. do the loopback on the swicth and will cause the arp storm. 2. check if the heatbeat LED is blinking and IPMI FW is alive. ----------------------------------------------------------------------------------------------- Filename: SMT_X10_151.bin version: 1.51 Date: 06-28-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: New Feature Description: [54095] [IPMI] No Email Alert Description for PCIE PERR and SERR Infected motherboard: X10DRC-LN4, X10DRC-T4, X10DRI-T4 Affected functions: Validation : 1. Set the SMTP. 2. Trigger the PCI PERR and SERR. 3. Check the event log. 4. Check the email. 2. Category: Fix Description: Add VmemVRM sensor Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. Do reset factory default once 2. Check VmemVRM sensors 3. Category: Fix Description: [54224][ SUM 1.3.0 ] Reset IPMI will clear all bin files. Infected motherboard: X10SRL-F Affected functions: Validation : After reset IPMI , run some command will not success , such as "Clear Event Log". e.g. ./sum -i 10.135.171.134 -u ADMIN -p ADMIN -c ClearEventLog 4. Category: New Feature Description: Support sensor support X10DRT-H, X10DRG-Q Infected motherboard: X10DRT-H, X10DRG-Q, Affected functions: Validation : 1. Check IPMI sensor reading page 5. Category: Fix Description: [54178] SEL gets filled with Drive Fault logs Infected motherboard: X10DRC, X10DRW Affected functions: Validation : 1.Create 8 Raid 0 HDDs 2.Do cuburn on/off 3.Check if there is a false alarm about HDD event sel log 6. Category: Fix Description: [53739] Fan speed goes up and down during post in Standard Mode Infected motherboard: X10DBT Affected functions: Validation : 1.Power on the SUT 2.Change the fan mode to the standard mode 3.Monitor Fans to see their fan speed. 7. Category: Fix Description: [54330] Xeon Phi fan function failed and all fans are at full speed Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1.Check fan control function with Xeon Phi card 8. Category: Fix Description: [54372] IPMI sensor reading webpage only shows 3 PCIe SSD temp, it should be 4 as I have 4 ports on mb Infected motherboard: X10DDW Affected functions: Validation : 1.Check if there are 4 SSDs appear on the NvME web page 9. Category: Fix Description: [54390] No NVMe drive location menu in IPMI Web GUI Infected motherboard: X10DBT Affected functions: Validation : 1.Check if there are 4 SSDs appear on the NvME web page 10. Category: fix Description: [53921] Fan pulse width modulation test fail Infected motherboard: X10SLH-N6-ST031 Affected functions: Validation : 1. Heat the LAN chips and see if pwm cycle heated 2. Power on the system, measure the pmw cycle is 50% in 40 seconds after system is powered on 3. Power off the system and power on, measure the pmw cycle is 50% in 40 seconds. ----------------------------------------------------------------------------------------------- Filename: SMT_X10_150.bin version: 1.50 Date: 06-13-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: New Feature Description: Support NvME function Infected motherboard: X10 Grantley platform (Smbus no.7 for X10DDW, Smbus no.4 is for X10DBT. Other Smbus no.3). Affected functions: Validation : 1. Insert NvME Add on card on PCIe slot 2. BMC will automatically detect and Add 2 NvME temperature sensors at least one PCIeSSD HDD is plugged in 3. BMC will remove NvME sensors once No PCIeHDDs is populated. 2. Category: New Feature Description: [53550] VRM sensor reading are "Not Present!" Infected motherboard: X10DRFF, X10DRFR Affected functions: Validation : 1. Power up the SUT. 2. Login the WebGUI to see the sensor page. 3. Category: Fix Description: [54064] 10GLAN Temp sensor reading is incorrect Infected motherboard: X10DRG-H(T) Affected functions: Validation : 1. Uncheck Preserve Configuration when upgrade IPMI. 2. Reboot system. 3. Verfiy X10DRG-HT has 10GLAN Temp. (X10DRG-H is 1G LAN model; X10DRG-HT is 10G LAN model) 4. Category: Fix Description: [54031] IPMI Configuration: Changes on Port settings can not be saved Infected motherboard: X10 motherboards Affected functions: Validation : 1. Change port setting in Configuration category. 2. Check services are going to direct to new port 5. Category: Fix Description: [54092][ SUM 1.3.0 ] SMCIPMITool Raw command will cause DMI issue. Infected motherboard: X10 motherboards Affected functions: Validation : Run the follow command to see if it is ok. ./sum -i 10.135.171.134 -u ADMIN -p ADMIN -c GetDMIInfo --file D_Cfg-X10SRL/dmi_first.txt --overwrite 6. Category: Fix Description: [54081]After update IPMI V1.49 FW, system will generate "Processor Thermal Trip - Asserted" message in Event Log [54041]CPU thermal trip 1.49 IPMI [54093]IPMI logs "Processor Thermal Trip - Asserted" in event log every time the system is powering down [54098]IPMI sel recorded "Thermal Trip" while system reboot or shutdown. Infected motherboard: X10 motherboards Affected functions: Validation : 1. do unit reset on web. 2. check if there will not be the thermal trip event log. 7. Category: Fix Description: [54102] FAN6 fan fail action is incorrect. Infected motherboard: X10SRW-F Affected functions: Validation : 1. Insert fans on FAN6 and FAN7 connectors.Then enter IPMI sensor page 2. pulled out FAN7 connector, check if BMC would show FAN6 and FAN7 fail. 8. Category: Fix Description: [54031] Fan speed goes up and down during post in Standard Mode Infected motherboard: X10DBT Affected functions: Validation : 1. Update both of two X10DBT motheboards. 2. Power on both of two X10DBT motherboards. And wait them to OS. 3. Keep them idle. 4. Observe the Fan behavior. 9. Category: Fix Description: [54102] FAN6 fan fail action is incorrect. Infected motherboard: X10DBT Affected functions: Validation : 1. Pulled out FAN6 connector. 2. Check the WebGUI. 3. Pulled out FAN7 connector. 4. Check the WebGUI. 10. Category: Fix Description: High NR of CPU temp always show 'N/A', and sensor show green color if the value locates between UC to LC Infected motherboard: X10 series Affected functions: Validation : 1. checking sensor readings web page that 1-1 if the threshold Hing NR of CPU Temp show 'N/A' 1-2 showing the sensor green while the reading value is between UC and LC showing the sensor yellow while the reading value is between UC and UNR or between LC and LNR. showing the sensor red while the reading value is upper then UNR or lower then LNR ----------------------------------------------------------------------------------------------- Filename: SMT_X10_149.bin version: 1.49 Date: 06-06-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: CPU# Not Match Between Email Alert Event Description and IPMI Event Log Infected motherboard: X10 motherboards Affected functions: Validation : 1. Setup the smtp account and trigger the Memory ECC command 2. Compare between the CPU number inside email and another one inside sel logs. It should be the same 2. Category: New feature Description: Add CPU thermal trip Infected motherboard: X10 motherboards Affected functions: Validation : 1. heat CPU until the system shut down. 2. we will have the event log of the thermal trip on IPMI web. 3. Category: fix Description: [53558] [IPMI] FANs on right zone and left zone DO NOT run lowest speed when there is NO GPU detected Infected motherboard: X10DRG-H Affected functions: Validation : 1. Check if the fan speed is following middle cooling zone when some other unsupported GPU or PCIe cards installed 4. Category: fix Description: [53433] SUM 1.3.0 - ChangeBMCcfg fail. [53746] [SUM 1.3.0 ] Invalid BMC configuration text file. Infected motherboard: A1SA2 Affected functions: Validation : 1. issue the follow SUM commands. a. sum -i IP -u ADMIN -p ADMIN -c getbmccfg --file bmc.cfg b. sum -i IP -u ADMIN -p ADMIN -c changebmccfg --file bmc.cfg 5. Category: fix Description: [53946] [IPMI ECO] CPU# Not Match Between Email Alert Event Description and IPMI Event Log [53522] IPMI] Email Alert Event Description Not Shown For Memory ECC Error Assertion Infected motherboard: All motherboard Affected functions: Validation : 1. Set the SMTP. 2. Generatre Ecc events. 3. See the Email. 6. Category: fix Description: [53944] VmemVRM temperature missing Infected motherboard: X10DRL-i Affected functions: Validation : 1. Power up the SUT. 2. Check the WebGui. 7. Category: fix Description: [53985] Upper Non-Critical Event logged in IPMI SEL Infected motherboard: X10DRC-T Affected functions: Validation : 1. Heat the LAN chips and check if upper Non-Critical event is issued. 8. Category: fix Description: [53921] Fan pulse width modulation test fail Infected motherboard: X10SLH-N6-ST031 Affected functions: Validation : 1. Heat the LAN chips and see if pwm cycle heated 2. Power on the system, measure the pmw cycle is 50% in 40 seconds after system is powered on 3. Power off the system and power on, measure the pmw cycle is 50% in 40 seconds. ----------------------------------------------------------------------------------------------- Filename: SMT_X10_148.bin version: 1.48 Date: 05-23-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Enhancement Description: The overheat criteria is changed to DTS - 0 when cpu is overheated. Follow the latest Thermal Guide SIM_TDG REV. 4.01 (05292014).pd) Infected motherboard: X10 motherboards Affected functions: Validation : 1. Change the overheat condition occurs 2. Category: fix Description: [53739] Fan speed goes up and down during post in Standard Mode Infected motherboard: X10DBT Affected functions: Validation : 1. Set the fan mode to Standard Mode. 2. Power up the SUT. 3. Wait about 90 seconds. (Temperature sources will have keen competition during this time.) 4. Make sure no scripts are running. 5. Observing the fan speed. 3. Category: fix Description: [53871] There is no Power supply info present under IPMI webgui sensor reading page. Infected motherboard: X10QBi Affected functions: Validation : 1. Login the WebGui and switch to the Sensor Readings page. 4. Category: fix Description: [53522] [IPMI] Email Alert Event Description Not Shown For Memory ECC Error Assertion. Infected motherboard: All motherboards Affected functions: Validation : 1. Set the SMTP. 2. Generatre Ecc events. 3. See the Email. 5. Category: fix Description: [53809] Power supply sensor missing with IPMI 1.47 Infected motherboard: X10DRG Affected functions: Validation : 1. Login to the sensor reading page of WebGUI 6. Category: fix Description: [53728] IPMI user privilege settings are incorrect Infected motherboard: X10DRU-I Affected functions: Validation : 1. Using user account that privilege is USER/OPERATOR to login web page. 2. Check mouse mode and sel page. ----------------------------------------------------------------------------------------------- Filename: SMT_X10_147.bin version: 1.47 Date: 05-23-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: fix Description: [53522] [IPMI] Email Alert Event Description Not Shown For Memory ECC Error Assertion. Infected motherboard: X10DRC and X10DBT Affected functions: Validation : 1. Set the SMTP. 2. Generatre Ecc event. 3. See the Email. 2. Category: fix Description: [53512] Zone two(Fan A,B,C,D) always keep in 46.3% at HeavyIO mode [53552] [IPMI] FSC doesn't follow thermal guideline when only one GPU is heating up Infected motherboard: X10DRG-H Affected functions: Validation : 1. Need to reset factory default once for X10DRG-H. 2. Use PCH FSC profile for GPU sensors at HeavyIO mode. 3. Only optimal, heavy I/O, and full speed fan modes are options (optimal mode is the default setting). 4. Check fan speed control for all GPU slots in different fan mode. 3. Category: fix Description: [53558] [IPMI] FANs on right zone and left zone DO NOT run lowest speed when there is NO GPU detected Infected motherboard: X10DRG-H Affected functions: Validation : 1. When Full Speed Mode is chosen, all fans run at full speed 2. When there is no card detected on PCI-E slot 1, 2, 3, 4, 5, or 6, Fans A-H remain on the lowest fan speed 4. Category: fix Description: [53586] Four fan sensors are missing Infected motherboard: X10DRU-I+ Affected functions: Validation : Login web GUI and check sensor reading. 5. Category: fix Description: [53588] The power supply sensor reading is incorrect [53624] The multi node monitoring function should not show on IPMI WebGUI [53581] No power fail led [53585] No Overheat LED When CPU overheat Infected motherboard: X10DRU-I Affected functions: Validation : 1. Login to the sensor reading page of WebGUI 6. Category: fix Description: [52449] Voltage sensors reading are gone after BMC reset on X10SLM-F Infected motherboard: X10SLM-F Affected functions: Validation : 1. Check the IPMI web gui to see if all adc sensors are gone when sensors are starting polling 7. Category: fix Description: [53621] The VmemVRM Temp sensor readings are showing N/A Infected motherboard: X10DRU-I Affected functions: Validation : 1. Login to the sensor reading page of WebGUI 8. Category: fix Description: [53623] The description for BIOS Resileence is incorrect and the help description is missing Infected motherboard: X10DRU-I Affected functions: Validation : 1. Login to the BIOS Resilience page of WebGUI 9. Category: fix Description: [53463] Event log gets filled with SEL that is not related Infected motherboard: X10DBT Affected functions: Validation : 1. Clear the SEL first. 2. Power cycle the SUT. 3. Check the SEL. 10. Category: fix Description: [53728] IPMI user privilege settings are incorrect Infected motherboard: X10DRU-I Affected functions: Validation : 1. Using user account that privilege is USER/OPERATOR to login web page. 2. Check mouse mode and sel page. ----------------------------------------------------------------------------------------------- Filename: SMT_X10_146.bin version: 1.46 Date: 05-xx-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: fix Description: [53388] IPMI web-gui detects wrong speed for shared LAN [53465] Network speed in IPMI web-gui shows 100M when connected to shared network Infected motherboard: X10DRC and X10DBT Affected functions: Validation : 1. go to the network page and check if the link status of the share lan. 2. Category: fix Description: [47450] [EVT] JI2C1 / JI2C2 header not Functioning [52571] Storage Monitoring needs to be enabled in IPMI for onboard 3108 [52410] IPMI sensor readings can't detection HDD status on AOM-S3108-H8 [52751] Storage Monitoring needs to be enabled in IPMI for onboard 3108 [52337] We can not see Storage monitoring page when installing LSI2208 storage card to the board Infected motherboard: X10DRC ,X10DRI,X10DRW,X10DRFF Affected functions: Validation : 1. check the phsical/Logic HDD status on Storage Monitoring page 3. Category: fix Description: [53381] Where does IPMI read the LSI ctrl temperature from? Infected motherboard: X10DRC Affected functions: Validation : 1. heat LSI chip and check if LSI Ctrl temperature sensor goes higher. 4. Category: fix Description: [52888] Power supply sensor missing Infected motherboard: X10DRG-H Affected functions: Validation : 1. check if power supply sensor presents 5. Category: fix Description: [53392] IPMI sensor issue: DIMMA2 is not working correctly Infected motherboard: X10DRG-H Affected functions: Validation : 1. install DIMMA2 and DIMMB1 separately 2. check if DIMMA2 and DIMMB1 present correctly 6. Category: fix Description: [53464] Some of the sensor readings show N/A Infected motherboard: X10DBT Affected functions: Validation : 1. check the sensor list in WebGUI or ipmitool 7. Category: fix Description: [52802] 5 LED Front Panel's OH doens't blink when there is power failure Infected motherboard: X10DRG-H Affected functions: Validation : 1. check if event is logged when there is power failure 2. check if 5 LED Front Panel's OH blinks 8. Category: fix Description: [53509] Peripheral temperature RT2 swapped with systemtemperature RT1 Infected motherboard: X10DRG-H Affected functions: Validation : 1. heat RT1/RT2 2. check if temperature goes up correctly 9. Category: fix Description: [53462] IPMI 1.45 fw has problems changing different fan speed mode [53527] HeavyIO FPWM failed Infected motherboard: X10DBT Affected functions: Validation : 1. Login to the fan mode page of WebGUI 2. Change the fan mode and see the fan speed. 10. Category: fix Description: [53125] Some SDIII readings are incorrect Infected motherboard: X10SRI Affected functions: Validation : 1. Run the SD3 and see the result. 12. Category: fix Description: [53536]CPU overheat cause OS reboot and alarm & LED won't turn off after reboot on X10DRC-T4+ Infected motherboard: X10DRC Affected functions: Validation : 1. do CPU overheat test and LED will be on. 2. reboot system and check if LED will be off when cpu is not in overheat state 13. Category: fix Description: [53588] The power supply sensor reading is incorrect [53586] Four fan sensors are missing Infected motherboard: X10DRU-I Affected functions: Validation : 1. Login to the sensor reading page of WebGUI 14. Category: fix Description: [53581] No power fail led Infected motherboard: X10DRU-I Affected functions: Validation : 1. Create a power fault, ex: AC loss, and check power led ============================================================= Filename: SMT_X10_145.bin version: 1.45 Date: 05-08-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 ***A1SA2 Production Release*** Notice:Please read the item 1 description when you update node2 FW. 1. Category: Enhanecement Description: The BMC slave address is changed to 0x20 Infected motherboard: The node 2 of A1SA2 Affected functions: Validation : FW update though web 1. Update this FW but keep the check on the preseve box on the FW update web page 2. Wait for updating and bmc will reboot 3. Then execute "Factory default" on IPMI web page 4. Use ipmitool command, "ipmitool sdr" to see if sensor information is displayed correctly FW update though dos 1. execute "ADupdate -f SMT_X10_145.bin -r y" (Preseve the original setting) 2. Wait for updating and bmc will reboot 3. Then execute "ipmicfg -fd" to do factory default 4. Use ipmitool command, "ipmitool sdr" to see if sensor information is displayed correctly 2. Category: Fix Description: [53313] No Alert LED or IPMI event log when CPU overheat Infected motherboard: X10DRG-H Affected functions: Validation : 1. Need to reset factory default once for X10DRG-H. 2. Check if IPMI event is logged when CPU overheat 3. Category: Fix Description: [53024] Jordan Creek Memory Buffer Temperature not available in IPMI Infected motherboard: X10DBT Affected functions: Validation : Note: Please make sure the A1 should be the first DIMM slot. If A1 does not have DIMM, the JC sensor would not be shown. 1. Check the sensor list page or sensor list command. 4. Category: Fix Description: [53347] Always full fan with IPMI 1.44 Infected motherboard: X10DRW-I Affected functions: Validation : 1. Check the fan sensor in the WebGUI or sensor list command. 5. Category: Fix Description: [53377] CPU temperature status readings are still showing values in IPMI Multinode monitoring status page when the node is off Infected motherboard: X10DRFR Affected functions: Validation : 1. Check IPMI multinode web page 6. Category: Fix Description: [53356] CPU temperatures are not shown correctly under IPMI Web GUI multinode page Infected motherboard: X10DRFR Affected functions: Validation : 1. Check IPMI multinode web page ============================================================= Filename: SMT_X10_144.bin version: 1.44 Date: 05-06-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 ***X10DRI Beta Release*** 1. Category: Fix Description: [52867] FAN sensors in IPMI are incorrect Infected motherboard: X10DRG-H Affected functions: Validation : 1. Disconnect FAN A, B, C and D(according to MB silkscreen). 2. Check if IPMI logs correct event log. 2. Category: Fix Description: [53112] Battery voltage reading fail Infected motherboard: X10DRG-H Affected functions: Validation : 1. Need to reset factory default once for X10DRG-H. 2. Verify the reading of VBAT. 3. Category: Fix Description: [53072] CPU2 VRM Temperature not available in IPMI Infected motherboard: X10DBT Affected functions: Validation : 1. Verify the reading of CPU2 VRM. 4. Category: Fix Description: [53100] IPMI firmware 1.41 (1.43 cannot see CPU3 Temp & CPU4 Temp) Infected motherboard: X10QBi Affected functions: Validation : 1. Check the CPU3 Temp and CPU4 Temp value. 5. Category: Fix Description: [52396] FAN always run full speed Infected motherboard: X10SLM+-LN4F Affected functions: Validation : 1. Please left system idle overnight and see if FANs speed is at the full speed. 6. Category: Fix Description: [53164] No LSI Ctrl Temp in IPMI Web GUI Infected motherboard: X10DRW-I Affected functions: Validation : 1. please check if LSI sensor has reading. (be noted the motherboard must be reworked) 7. Category: Fix Description: [47450] I2C1 / JI2C2 header not Functioning Infected motherboard: X10DRI-T Affected functions: Validation : 1.please check if there is the storage monitoring on ipmi web. 8. Category: Enhancement Description: New backplane is supported on X10DRFR Infected motherboard: X10DRFR Affected functions: Validation : 1.Please use new backplane and use IPMI 1.44 after. 9. Category: Enhancement Description: Support A1SA2 HW reversion 1.02 Infected motherboard: A1SA2 Affected functions: Validation : ============================================================= Filename: SMT_X10_143.bin version: 1.43 Date: 04-xx-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [52591] Processor error message during SAT test on X10SLM-F Infected motherboard: All motherboard with ME Affected functions: Validation : 1. Run SAT 24 hour test. 2. Check the SEL and Error messages. 2. Category: Fix Description: [52118] Node 2 CPU overheat will not trigger Alert LED to turn solid on Infected motherboard: X10SLE-DF Affected functions: Validation : 1. Let CPU overheat on node 2 2. Check if the Alert LED turns solid on 3 Category: Fix Description: [52495] No DIMM 2 to be detected on ipmi web [52716] No PCH Temp & memory dim temp reading in the IPMI Web GUI Infected motherboard: X10DRW Affected functions: Validation : 1. Check the sensor reading page of Web GUI 4. Category: Fix Description: [52967] Memory temperature doesn't show in IPMI Infected motherboard: X10SRH Affected functions: Validation : 1. Check the sensor reading page of Web GUI 5. Category: Fix Description: [52887] FAN always is full speed. [52886] Power status always is "Not Present" in IPMI Power Source page [52886] No any sensor reading in IPMI Infected motherboard: X10SLH-N6 Affected functions: Validation : 1. Check the sensor reading page of Web GUI. 6. Category: Fix Description: [52434] VDIMM sensor readings are correct but show "Upper Non-recoverable" error message Infected motherboard: X10DDW Affected functions: Validation : 1. Check VDIMM sensor value is normal 7. Category: Fix Description: [52093] IPMI "DIMM Temp" sensor reading show "Not Present" Infected motherboard: X10SRI Affected functions: Validation : 1. Check the sensor reading page of Web GUI 8. Category: Enhancement Description: add LSI Ctrl temp. sensor and do the fan control according to its temperature. Infected motherboard: X10DRW X10DRC Affected functions: Validation : 1. Please do the reset-to-default 2. Check if LSI Ctrl sensor on IPMI web. 9. Category: Fix Description: [52859] vmem VRM readings missing Infected motherboard: X10DRL-I Affected functions: Validation : 1. Check the sensor reading page of Web GUI ============================================================= Filename: SMT_X10_142.bin version: 1.42 Date: 04-xx-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [52620] [BIOS] CTLM Memory Throttling Not Working [52730]CLTM Memory Throttling Not Working. Infected motherboard: X10SLH and X10SLM Affected functions: Validation : 1. heat on the memory and see if the memory throttling works. 2. Category: Fix Description: [52682] Event logs get filled with Vmem temperature logs [52675] IPMI sensor reading abnormal [52671] VmemVRM Temp senosr reading abnormal [52661] X10SRI-F system got "Lower Non-recoverable" error drung the CPU linpack testing Infected motherboard: X10 motherboard with Grantley CPUs Affected functions: Validation : 1. Check the memory VRM values are normal on IPMI web gui 2. Do linpack testing to see if event log is issued 3. Category: Fix Description: [52671] VmemVRM Temp senosr reading abnormal Infected motherboard: X10 motherboard with Grantley CPUs Affected functions: Validation : 1. Check the memory VRM values are normal on IPMI web gui 2. Do linpack testing to see if event log is issued 4. Category: Fix Description: [52464]Inconsistent behavior under IE9/Chrome/Firefox/Safari after prompt for updating Java in IPMI webpage Infected motherboard:A1SA7 Affected functions: Validation : 1. in IPMI webpage, if one clicks 'system information' menuitem, a dialog box will prompt if necessary to update java 2. click "yes" and check if you can get the same behavior using the different browsers. 4. Category: Fix Description: [52191]IPMI Web Report Wrong Node Position Infected motherboard:X10DRT-P Affected functions: Validation : 1.login in other nodes except node A. 2.Enter multinode page and check currnet node ============================================================= Filename: SMT_X10_141.bin version: 1.41 Date: 04-16-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r22 1. Category: Fix Description: [49610] There should not be more than one IPMI console redirection allowed from IPMI webgui. Infected motherboard: All Affected functions: Validation : the goal for this enhancement is to avoid the users do the harmful thing to the system when the bios is updating though OOB. 1. while bios is updating though web/SUM,iKVM viewer will got the notification and close itself. 2. while the bios is updating through web/SUM, the user can't launch iKVM viewer. 2. Category: Fix Description: [52663] [IPMI Firmware v1.40 ECO]No SNMP Trap, Email Alert and Event Log when CPU Overheat Infected motherboard: X10QBi X10DRi-T X10DRi-T_10G Affected functions: Validation : 1. Make CPU overheat, and then check the SEL, SNMP Trap, Email 3. Category: Fix Description: [52301] Failed to boot from CDROM & Floppy by ipmitool. Infected motherboard: X10DRL Affected functions: Validation : 1. ipmitool chassis bootparam get