IPMI Firmware Release Note ---------------------------- Filename: SMT_X10_127.bin version: 1.27 Date: 01-06-2014 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 Category: New feature Description: OOB server Asset management -DDNS Infected motherboard: All Affected functions: ddns function on ipmi web Validation : 1. go to DDNS page and verify if it works. Category: New feature Description: Add X10DRFR sensor suppport Infected motherboard: X10DRFR Affected functions: Validation : 1. Category: Fix Description: [49994] [EVT] Teperature sensor are showing incorrect in IPMIWeb GUI [49992] [EVT] Voltage sensor "VBAT" shows "Upper Non-Recoverable" error in IPMIWeb GUI Infected motherboard: X10DRL-I Affected functions: Validation : 1. Check IPMI sensor status on web page Category: Fix Description: [49988] [EVT] IPMI Sensor Readings shows VBAT voltage as 13.545 volts [49992] [EVT] IPMI event log shows LAN TEMP as 127 degrees C Infected motherboard: X10DRL-I Affected functions: Validation : 1. Check IPMI sensor status on web page Category: Fix Description: [49958] SMCIPMITool NM command is not work Infected motherboard: A1SA2 Affected functions: Validation : 1. Use nm20 command by smcipmitool Category: Fix Description: [49860] Fan PWM measurement fail [49802] Hardware monitor fail [49799] Sensor readings are fail Infected motherboard: A1SA2 Affected functions: Validation : 1. Check if fan sensor exists on IPMI web page 2. Check if we can see all sensors on BMC2 IPMI web page Category: Fix Description: [49788] The date format are different. Infected motherboard: All Affected functions: Validation : 1. Check if BMC build date format is the same as Bios Category: Fix Description: [49476] No GPU temperature reading shown in IPMI Web GUI Infected motherboard: X10QBI Affected functions: Validation : Support KNC and Kelper. Category: Fix Description: [49227] Fan PWM Test Fail Infected motherboard: DRI_T, DRI Affected functions: Validation : 1. Check IPMI web page if sensors are good Category: Fix Description: [49318] FPWM Heavy IO mode does not start from 50% duty cycle Infected motherboard: QBI Affected functions: Validation : 1. Set the HeavyIO mode on QBI and power on. Measure the pwm cycle. Category: Fix Description: [48951] FPWM Heavy IO mode does not start from 50% duty cycle Infected motherboard: QBI Affected functions: Validation : 1. Set the HeavyIO mode on QBI and power on. Measure the pwm cycle. Category: Fix Description: [48951] Fan PWM Test Fail [49992] Infected motherboard: X10SRE-DS018 Affected functions: Validation : 1. Check IPMI sensor status on web page ---------------------------- Filename: SMT_X10_126.bin version: 1.26 Date: 12-25-2013 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 **For X10DRI_T, X10DRI beta release only Category: Fix Description: [49762] Can't login to SUT IPMI IP by ipmi command during SUM test, but can login by web browser Infected motherboard: X10SLL Affected functions: Validation : 1. doing SUM stress test and see if SUM failed to login to IPMI firmware. Category: Fix Description: [49762] Can't login to SUT IPMI IP by ipmi command during SUM test, but can login by web browser Infected motherboard: X10SLL Affected functions: Validation : 1. doing SUM stress test and see if SUM failed to login to IPMI firmware. Category: Fix Description: [49656] VRM temperatures don't present and Naming doesn't follow thermal guildeline Infected motherboard: X10DRI, X10DRI_T Affected functions: Validation : 1. Enter IPMI sensor page to see if only one VRM sensor exists Category: Fix Description: [49641] CPUs reading got disappeared after a while with 12-10-2013 bios & IPMI FW 1.24 Infected motherboard: X10DRI, X10DRI_T Affected functions: Validation : 1. Power On & Off the system to see if cpu sensor is missing Category: Fix Description: [49640] IPMI system power consumption monitoring is misbehaving Infected motherboard: X10SLE-DF Affected functions: Validation : 1. AC unplugged & plugged the system, and check the values of power consumption are correct (power consumption web page) Category: Fix Description: [49609] IPMI Web GUI shows incorrect IPMI Share LAN link status when the cable is unplugged. Infected motherboard: All Affected functions: (1)the network connectivity under all lan modes. (2)switch lan mode,e.g. switch the failover mode to share or dedicated mode. Validation : (1) Connect cables to both IPMI Share and delicated LAN (2) Check IPMI Web GUI -> Configuration -> Network -> Network Link Status. It shows both are connected (3) Then remove cable from Share LAN and check the network link status again. Category: Fix Description: [49605] there are no DIMMs temperature readings under IPMI webgui sensor reading page Infected motherboard: X10DRI, X10DRI_T Affected functions: Validation : 1.Enable the CLTT mode 2.there are no DIMMs temperature readings under IPMI webgui sensor reading page Category: Fix Description: [49415] Fan Pulse-Width-Modulation Measurement fail Infected motherboard: X10SRE_DS018 Affected functions: Validation : 1.Enable the CLTT mode 2.there are no DIMMs temperature readings under IPMI webgui sensor reading page ---------------------------- Filename: SMT_X10_125.bin version: 1.25 Date: 12-13-2013 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 [New feature] Description: SMC RAKP Infected motherboard: ALL Affected functions: IPMI Lan connection Validation : 1.Please use SMCIPMITool 2.6.4 in project board id = 1360. 2.To enable SMC RAKP in misc SMC RAKP page. 3.Modify SMCIPMITool.properties(oem_rakp=on/off). 4.use SMCIPMITool to connect BMC via Lan Usage: smcipmitool ADMIN ADMIN ipmi sr 5.when oem_rakp=on, SMCIPMITool can connect to BMC. when oem_rakp=off,SMCIPMITool cannot connect to BMC. 6.To disable SMC RAKP in misc SMC RAKP page. use SMCIPMITool to connect BMC via Lan 7.when oem_rakp=on, SMCIPMITool cannot connect to BMC. when oem_rakp=off,SMCIPMITool can connect to BMC. [Enhancement] Category: Enhancement Description: A1SA2, X10DRFF and X10DRW_I board support Infected motherboard: A1SA2, X10DRFF and X10DRW_I Affected functions: BMC2 is not supported yet (A1SA2) Validation : Category: Enhancement Description: [Production request]add bios revision when doing bios update through web and SMCIPMItool Infected motherboard: All Affected functions: (1) BIOS update on web. (2) OOB BIOS update Validation : (1) make sure the bios image can support bios revision. otherwise,it is not shown. (2) do bios update through web and SMCIpmitool. Category: Enhancement Description: Enhance the polling time for VBAT sensor to make it more durable Infected motherboard: All Affected functions: All Validation : make sure if any VBAT event logs appears when doing the on-off stress test or c-burn test. [Fix] Category: Fix Description: [49373] IPMI WebGUI not working properly after updating to version 1.24 Infected motherboard: X10QBI Affected functions: NONE Validation : login in IPMI web by using Firefox/IE/chrome and check if it works. Category: Fix Description: [49373] Fan PWM measurement fail Infected motherboard: X10SLX-F Affected functions: NONE Validation : measure descending fan curve Category: Fix Description: BMC's NM Discovery SDR is incorrect.Please take a look at attached and see the last 4 bytes. Infected motherboard: The motherboard with ME function Affected functions: It just not fit the standard Validation: Use smcipmitool to key in "nm20 nmSDR". It should like the following values Health Event Sensor Number = 25h Exception Event Sensor Number = 24h Operational Capailities Sensor Number = 26h Alert Threshold Exceeded Sensor Number = 27h ---------------------------- Filename: SMT_X10_124.bin version: 1.24 Date: 11-29-2013 U-Boot build time : 2009.01 (Nov 27 2013) Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 [Enhancement] Description: Add firmware recovery Infected motherboard: ALL Affected functions: 1. firmware upgrade through http and https 2. firmware upgrade though dos/windows/linux utilities. Validation : 1. make sure the firmware 1.24 or later resides in the flash 2. upgrade the firmware and plug off the power cable during fw upgrade. 3. plug in the power cable and then recover the firmware using the dos adupate under dos. Description: Support SUM to upgrade firmware. Infected motherboard: ALL Validation : 1. make sure the SUM version and MUST use the version after "1.2.0 2013/11/14".(this version is not included). 2. make sure the IPMI firmware version and MUST use 1.24 or later.(include 1.24) 3. upgrade the firmware using SUM tools via https and http. Please refer to the SUM document to learn the usage. [Bug fix] Description: The security holes about implementing the numerous unsafe string function through web interface Please refer to the followinginfromation on CVE web site CVE-2013-3623,CVE-2013-3622,CVE-2013-3621,CVE-2013-3623 Infected motherboard: ALL. Affected functions: all web functions. Validation: Check if all functinons on web works . Description: The fan fail pin will be set output high at BMC Initialization (X10SRE-DS018 HW requirement) Infected motherboard: ALL. Validation: Please test fan failed funciton to see if this function works. [49236] System cannot be booted up with IPMI 1.23 Infected motherboard: X10DRI, X10SRE-DS018 Validation: Power off the motherboard and power on again. [49292] Email alert motherboard name is wrong Infected motherboard: X10DRI Validation: Setup email alert and check the tile [49140] Watchdog Timer test failed Infected motherboard: X10QBI Validation: Boot system to bios setup menu--> Boot Feature--> "Enabled" Watch Dog Function--> Save Changes & boot to OS--> Leaving system IDLE--> Result: Watchdog Timer test failed [48963] Lower Critical - Going Low - Asserted during system on/off test on X10SLL-F Infected motherboard: X10SLL-F Validation: System on/off test, 5VCC event log occurs [48477] Fan PWM measurement fail Infected motherboard: X10SLX-F Validation: measure descending fan curve of CPU, PCH. measure the all curves of RT2 ===================================================================================== Filename: SMT_X10_123.bin version: 1.23 Date: 11-15-2013 SVN: 906 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 Feature: Solve: Heart beat & UID LED funcitons work not properly [validation steps] Power on the machine and setup the UI light [Root cause] Multifunction does not setup ===================================================================================== Filename: SMT_X10_122.bin version: 1.22 Date: 11-15-2013 SVN: 882 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 Feature: Solve: ==> Please clear broswer cache to veriy LDAP problem [49070,49068] IPMI-LDAP setting problem [Validation steps] enter ',', ';' character in in the text filed of Bind DN and Searchbase in LDAP page [Root cause] The user cannot input ',', ';' in the text filed of Bind DN and Searchbase due to security issue, there is flicker screen in the ikvm viewer. [validation steps] 1. Launch IKVM viewer 2. switch to the high resolution under OpenSUSE 12.03 and Ubuntu 13.04 [Solution] Provide the solution to fix VGA BIOS and VGA driver version mismatch. ===================================================================================== Filename: SMT_X10_121.bin version: 1.21 Date: 11-08-2013 SVN: 882 U-Boot build time : Nov 08 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 Feature: Solve: ==> Please remove current FruData by ipmicfg command (ipmicfg -raw 30 41 and then wait for bmc reboot) X10 Up boards, Dp boards Fru1 data cannot write [Validation steps] 1.Please remove current FruData by ipmicfg command (ipmicfg -raw 30 41 and then wait for bmc reboot) 2.ipmicfg -fru1 list. Check if fru1 data exists 3.jipmicfg -fru1 bp 1. Check if bp is equal to 1 [48818] Uncorrect information in Power Source monitoring [Validation steps] check dc12output voltage, ac input current, dc 12 output current (ps source webpage) [Root cause] Correct the formula toward these values X10SLX-F [48477] Fan PWM measurement fail [Validation steps] measure descending fan curve [Root cause] It doesn't change the fan curve when descending [48763] CPU temperature only can up to 85 degree C with E3-1220L v3 CPU hence the fan speed can't run at full speed [Validation steps] Select CPU which HighNR is under 90 degree and try to overheat it. [Root cause] Old FW doesn't consider the case when Tjmax is lower then 90 degree X10QBI [46732] HWM test fail [Validation steps] Check VBAT sensor voltage, should be close to 3.3v [Root cause] The typical voltage of battery component is 3.3v [Solution] Modify SDR A1SAM-F [46732] JL1 chassis intrusion jumper is not working. [Validation steps] put JL1 jumper on, and then pull out. See if chassis intrusion still exists [Root cause] BMC should keep chassis intrusion state until this state resets ===================================================================================== Filename: SMT_X10_120.bin version: 1.20 Date: 11-01-2013 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 Feature: Solve: All X10 mother boards [48758] Unable to login to ADMIN account after changing passwords a few times [Validation steps] 1. Login to IPMI Web GUI -> Configuration -> Users -> Modify ADMIN 2. Change ADMIN password to ADMIN123 3. Check ipmitool remotely with new password 4. Change ADMIN password to ADMINADMIN 5. Check ipmitool remotely with new password 6. Change ADMIN password to ADMIN123 7. Check ipmitool remotely with new password [Root cause] there are garbage byte left at the end of the new password [48612] Power Fail Email Alert Does Not Have Event Description to Mention Power Fail Event [Validation steps] Install power supply and pull out the power cord [Root cause] Need to parse sel data to show power failure information before email alert is sent [48477] Fan PWM measurement fail [Validation steps] measure the heavy io curve on cpu and dimm [Root cause] Should follow the spec of X10 SIM_TDG Draft 06282013.pdf to setup heavy io curve on cpu and dimm X10SLA-F [48762] FAN sensor reading of 20,000 rpm FAN is not correct [Validation steps] install the fan and set full speed mode. Check if rpm is over 20000 [Root cause] Fan rpm calculation occurs overflow on high speed fan X10SLE-DF [48606] iKVM Does Not Identify Node By Name [Validation steps] Enter IPMI web page and see the host names on both node, "SLE_D_NODE_1" and "SLE_D_NODE_2" [Root cause] We setup the host name to judge which bmc is used and logged in now ===================================================================================== Filename: SMT_X10_119.bin version: 1.19 Date: 10-28-2013 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r21 Feature: Solve: All X10 mother boards [48659] Cannot read/write FRU by smcipmitool.exe [Validation steps] Read: smcipmitool.exe ADMIN ADMIN ipmi fru Write: smcipmitool.exe ADMIN ADMIN ipmi fruw [Root cause] the command responses the data from the wrong FRU block [48423] The memory ECC even log fail [Validation steps] Use ipmi command to test Dimm A1 has ecc errors ipmitool -I lanplus -H 10.133.176.182 -U ADMIN -P ADMIN raw 0x4 0x2 0x4 0x0c 0xff 0x6f 0x1 0x1A 0x80 [Root cause] handle unused variable on event log web page X10SLD-EF [48322] PUE, Standard, and Heavy IO Fan Modes have the same Fan Speed [Validation steps] Set each fan mode and observe the rpms [Root cause] Micro cloud series servers are special cases. Heavy I/O mode can be removed. Fan speed table is changed [48609] Memory Sensor Does Not Match BIOS Setup Naming [Validation steps] Check IPMI sensor name and compare with the other on bios setup [Root cause] Add the mechanism to judege BMC 1 and BMC2 by GPIOH2 [48604] PCH Temperature Sensor Missing [Validation steps] Enter sensor page [Root cause] Need add PCH sensor for monitoring list A1SAI-F, A1SAM-F [48322] Fan Mode Setting fail. [Validation steps] Set heavy io mode and heat memory [Root cause] dimm sensor is not put in fan control list A1SAI-F, A1SAM-F [48322] Fan Mode Setting fail. [Validation steps] Set heavy io mode and heat memory [Root cause] dimm sensor is not put in fan control list X10QBI [48300] Abnormal IPMI Fan fail event logs [Validation steps] Power on at initialization [Root cause] bank 0, reigster should be set 0xF4 Add protection to avoid ghost fans noise X10SEAA-LN4F,X10SL7-F, X10SLA-F [48279] FAN speed won't change when overheat memory with setting Fan to HeavyIO Speed [Validation steps] Set heavy io mode and heat memory [Root cause] The curve of heavyIO mode is not configured ===================================================================================== Filename: SMT_X10_118.bin version: 1.18 Date: 10-09-2013 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Feature: @Support Fru inventory data 1 for PE & bios to write board information area @Support port change and enable/disable function on both port setting web page and oem commad -0x30 0x70 0x67 Get/Set ports & Services Request Data 1: 0/1 [Get/Set] Data 2: Port service 0: HTTP_PORT,1: HTTPS_PORT,2: IKVM_PORT,3:VM_PORT,4:SSH_PORT,5:WSMAN_PORT,6:HTTP_SERVICE, 7:HTTPS_SERVICE,8:IKVM_SERVICE,9:VM_SERVICE,10:SSH_SERVICE,11:WSMAN_SERVICE,12:SSL_REDIRECT Data 3-4 : [Set] Data 4: port number (LSB) Data 5: port number (MSB)" "[Get] Response [Get] Data1: completion code Data2: port number (LSB) Data3: port number (MSB) [Set] Data1: completion code" Solve: All X10 boards [48321] YFan speed reading is incorrect with FAN-0141L4 [Validation steps] install the fan and set full speed mode. Check if rpm is over 20000 [Root cause] Fan rpm calculation occurs overflow on high speed fan [48281] Your session has timed out. You will need to open a new session" error message popped when click "Post Snooping" in IPMIWeb GUI [Validation steps] Enter post snopping page [Root cause] response the wrong data to browser and cause time-out [48279] FAN speed won't change when overheat memory with setting Fan to HeavyIO Speed [Validation steps] Switch to heavyIO mode and heat memory. Check if fan speed is up [Root cause] BMC don't include dimm sensor in fan control list [48206] SMTP server won't work if "Sender's Address" set @ " " (NULL) [Validation steps] 1. Alert setting 2. SMTP server setting (w/ sender's address) 3. Send Test Alert 4. Checks email [Root cause] Some smtp server, it needs complete email name (BMCaabbccddeeff@X10SLM-F.com) X10SLX-F [48293] No CPU overheat alarm, jumper JOH1 no function [48236] CPU temperature reading shows "Not Present" in IPMI Web [Validation steps] Heat CPU temperature or enter sensor page [Root cause] BMC don't use peci to read cpu temperature X10SLH-F [48236] Cannot reset to the factory default (clean LAN) [Validation steps] ipmicfg -fde [Root cause] BMC will clear fru inventory area on this oem command X10SLM-F [48167] Ipmitool to check onboard LAN1 MAC address failed. [Validation steps] 1. Use 0x30 0x21 command to get system mac address 2. Compare this with another on the IPMI system information web page [Root cause] BMC don't completely to delete the data about system mac address X10SLL-F [47470] The MAC address that use IPMITOOL to fetch is not match with MB [Validation steps] 1. Use 0x30 0x21 command to get system mac address 2. Compare this with another on the IPMI system information web page [Root cause] BMC don't completely to delete the data about system mac address A1SAM-F [48322] Fan Mode Setting fail [48239] IPMI sensor reading [Validation steps] Enter sensor reading page [Root cause] Previous BMC FW doesn't support this board yet. ===================================================================================== Filename: SMT_X10_117.bin version: 1.17 Date: 09-27-2013 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: *All X10 Up boards [48112][48111] Error in launching iKVM console Application Error: Unable to launch the appication error when launch Console Redirection Screen (KVM) [Validation steps] 1. launch ikvm from the console redirection page. [root cause] the java viewer can't accept the empty hostname. [solution] pass the default the hostname to ikvm viewer if it is empty. ===================================================================================== Filename: SMT_X10_116.bin version: 1.16 Date: 09-26-2013 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: *All X10 Up boards [48089][48088] Email Alert not working with IPMI FW v1.15 [validation steps] 1. configure SMTP server and the e-mail address on SMTP and alert pages. 2. trigger CPU or other sensors overheat. [48090] Factory default is not working [validation steps] 1. do factory-to-default on Factory default page. *MB -X10QBI-O-P [48006] System info LED is not on when fan failed or cpu overheat [47511] LED test for FAN Fail test Fail *MB -X10SLE-DF-O-P [47796] Cannot set up IPMI configuration on web [validation steps] (1)go to the LDAP page (2)click Enable LDAP Authentication, it will pop up message from webpage and logout. *MB -A1SAI-2750F-O-P [47533] VCCP sensor error [validation steps] (1)enter sensor reading page [47539] System unable to power back on neither by power button nor power control (IPMIWeb) [Validation steps] (1)make sure the lan cable be plugged to the share lan2. (2)do power on/off stress through ipmitool over the share lan 2. ===================================================================================== Filename: SMT_X10_115.bin version: 1.15 Date: 08-30-2013 U-Boot build time : Aug 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: A1SAi-2750F/2550F Support 25MHz PWM frequency output [#47556] Failed to mount virtual drive via "Virtual Media --> CD-ROM Image" in IPMIWeb GUI Root cause: Need to add user/password account judgement Solution : FW Update [#47535] Failed to update BIOS via IPMIWeb GUI Root cause: This platform doesn't support ME. Solution : Ignore ME region [#46347] Overheat LED at "JOH1" was lit and blinking if any of FAN-Failure asserted. Root cause: GPOY3 OVERHEAT LED" and "GPOA3 PSU/FAN failure", they PWM together when FAN fails Solution : Setup GPIOY3 to lit JOH1 only X10SLE-DF [#47405] For cpu2 HWM measurement fail at Vbat Root cause: incorrect SDR [#47447] Please Remove Dedicated LAN Link Option Root cause: NIC speed is always 1G speed. Don't need to adjustify All X10 motherboards [#47470] The MAC address that use IPMITOOL to fetch is not match with MB. Root cause: IPMI still record old share lan adderess after updating the nic eeprom Solution : Synchronize the new share lan address Validation step: 1. flsah eeprom with SLM13.zip 2. use IPMITOOL and command IPMITOOL.exe -I lan -H 10.135.15.95 -U ADMIN -P ADMIN raw 0x30 0x21 3. The result is not match with the MAC address of MB. ===================================================================================== Filename: SMT_X10_114.bin version: 1.14 Date: 08-16-2013 SVN: 620 U-Boot build time : Jun 14 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: X10DRI-T [#47389] Missing FanA and FanB on the Sensor Reading Page Root cause: sensor number of FANA & FANB is not correct in FW Solution : Modify them in FW Validation step: See it in sensor reading page X10SLE-DF [#47397] Dedicated LAN Speed Always Shows 10M [#47196] Dedicated LAN Link Status Shows 10M Root cause: driver reading is not correct Solution : Modify in NIC driver Validation step: See it in network page [#47334] HWM measurement fail at Vdimm Root cause: sensor reading is not accruate Solution : Adjust SDR value Validation step: See in sensor page [#47193] After Update to IPMI FW 1.13, CPU Throttling to 800 MHz Observed Root cause: GPIOA4 pulls low Solution : Pull GPIOA4 high at BMC initialzation Validation step: heat cpu over 80 degree by PwrThermalUtil tool All X10 motherboards [#47198] Lan Interface Should be LAN Interface Root cause: Change "Lan"to all capital letters "LAN" Solution : Correct wordings in FW Validation step: See "LAN interface" in network page X10SLL+-F [#47309] Email Alert for X10SLL+-F Shows X10SLA_F in Subject Header Root cause: Typo error Solution : Correct wordings in FW Validation step: Setup email alert function ===================================================================================== Filename: SMT_X10_113.bin version: 1.13 Date: 07-29-2013 SVN: 553 U-Boot build time : Jun 14 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r20 ****** The user is not allowed to downgrade the fw from this release due to the security issue****** Improvement: 1.Renew default SSL certificate from 7/17/2013 to 7/17/2014 2.fix the security issue for the user password Encrypt the user password inside IPMI fw. Validation step: 1. add/delete/modify the username/password through web or ipmitool. 2. save/restore the ipmi configuration. [X10SLE-DF] 3.Add X10 SLE-DF sensor reading support 4.Add RTL8363SB for dedicate lan 1G Support Solve: X10SEAA-LN4F [#46904] FAN1 and FAN3 are not working properly. Validation step:Try full speed All X10Up board [#46720,46709] Memory ECC Error Email Alert Shows Wrong DIMM Slot Validation steps: 1.Register the smtp setting 2.Use ipmi command to test Dimm A1 has ecc errors ipmitool -I lanplus -H 10.133.176.182 -U ADMIN -P ADMIN raw 0x4 0x2 0x4 0x0c 0xff 0x6f 0x1 0x1A 0x80 3.Receive the email and check if the dimm slot number is the same as the other in IPMI event log [#46595] In iKVM, IPMI firmware not supports others keyboard layout style except of "English" type IKVM VERSION : 1.69.20 Validation steps: 1.Launched iKVM,go to input tab in preference tab. 2.change the keyboard layout. 3.none of keyboard layout are working expect for English one. [#46592] Sender's address of SMTP setting not works properly. Validation steps: 1.Remote login into SUT IPMIWeb GUI via IPMI IP 2.Setup an alert entry in "Alerts --> configuration" field 3.Setup SMTP server with sender's address in "SMTP" --> configuration" field 4.Send a test alert and then check email [#46409] Auto-resize windowsˇ¨ tab of iKVM is not working Validation steps: 1.Remote login-into SUT via IPMI LAN. 2.Launched iKVM, un-check the "auto-resize windows" tab under Option -> Preference -> Windows 3.Use mouse adjust iKVM windows size a failed, unable to adjust X10SLH-F,X10SLL+-F,X10SLM+-F,X10SLM+-LN4F [#46708] DIMM Temperature Sensor Naming Does Not Match Silkscreen Validation steps: 1.Burn the FW and don't preserve the configuration 2.Enter IPMI sensor reading page X10SLM+-F,X10SLH-F [#46714] Email Alert Shows X10SLH_F Validation steps: Register the smtp setting and send the email ===================================================================================== Filename: SMT_X10_112.bin version: 1.12 Date: 07-05-2013 SVN: 499 U-Boot build time : Jun 14 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: X10SLM-F, X10SLL-F [#46480] IPMI Logs Non-Critical Events.(CPU Temp) Validation step: heat the CPU temperature [#46141] Low Critical- Going Low during IPMI ON/OFF share LAN stress Validation step: System on-off test X10SEAA_LN4F [#46374] No beep when no memory connect to the system. Validation step: don't plug in the memory and power on the machine [#46233] CPU Temp" and "Chassis Intrusion" shows "Not Present Validation step: Enter IPMI sensor page ===================================================================================== Filename: SMT_X10_111.bin version: 1.11 Date: 06-26-2013 SVN: 474 U-Boot build time : Jun 14 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: [#46381] Chassis Intrusion Not Logged in Event log,SNMP trap and E-mail alert [#46373] Chassis Intrusion Not Logged in Even Log [#46349] While chassis intrusion asserted, no chassis intrusion event log was showed. No SNMP trap and Email alert as well ===================================================================================== Filename: SMT_X10_110.bin version: 1.10 Date: 06-21-2013 SVN: 462 U-Boot build time : Jun 14 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: X10SLM+_LN4F 2.[#46276] IPMI Web Orderly Shutdown Power Control Does Not Work X10SEAA_LN4F 3.[#46242] There is an extra "Optimal" Fan-mode was present in IMPIWeb GUI 4.[#46237] Power supply information are not LINE-UP in IPMIWeb GUI 5.[#46224] It will generate " Voltage VDIMM " after run E-burn SAT Test ===================================================================================== Filename: SMT_X10_109.bin version: 1.09 Date: 06-14-2013 SVN: 451 U-Boot build time : Jun 14 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: 1.Add sensor support on X10SEAA_LN4F 2.update sensor list according to IPMI_voltage_sensors_threhold_R01.xlsx 2.#46139 LAN 1 disconnect after IPMI factory default setting 2.#46132 -12V Events Lgged During IPMI KVM Stress 3.#45908,#45905 IPMI Logs Non-Critical Events 4.#45778 Remote Console Preview display is abnormal 5.#46059 Random - Update BIOS setting via OOB with option "--reboot" fail. 6.#46056 Random - The process is loop when update BIOS via OOB. ===================================================================================== Filename: SMT_X10_108.bin version: 1.08 Date: 06-06-2013 SVN: 432 U-Boot build time : May 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: 1.fine tune sensor values on X10DRI_T, X10QBI_F 2.#46010 Please Change FAN1 Sensor to FAN 3.#45939 Power Fail Logs About Every 5 Minutes 4.#45938 HeavyIO FSC: FANA RPM Higher at 39C and lower at 42C 5.#45937 HeavyIO FSC Mode FanA Speed Higher Than Thermal Guideline Specification 6.#45928,#45926,#45908,#45905 IPMI Logs Non-Critical Events 7.#44075 dmesg has a "ipmi_si: Error clearing flags: cc" error message after running E-burn stress ===================================================================================== Filename: SMT_X10_107.bin version: 1.07 Date: 05-30-2013 SVN: 417 U-Boot build time : May 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: Fine tune VBAT, -12V sensor threshold on X10SLM-F, X10SLL-F and X10XLM+_LN4F ===================================================================================== Filename: SMT_X10_106.bin version: 1.06 Date: 05-27-2013 SVN: 410 U-Boot build time : May 27 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r19 Solve: Please clear Java cache (iKVM verion is updated) Please uncheck the preserved box in firmware upload page 1.Add sensor on X10SLL+_F, X10QBI_T 2.#45801,#45725,#45725,#45481 [OOB] System Will Shutdown After Flash BIOS Via OOB and Reset . 3.#45712 There are many Vcore events in IPMI SEL when running eburn LIN test 4.#45621,#45785 IPMI Virtual Keyboard didn't have Swiss language item 5.#45682 FAN speed will up to 100% when IPMI initializing ===================================================================================== Filename: SMT_X10_105.bin version: 1.05 Date: 05-20-2013 SVN: 398 U-Boot build time : May 20 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r18 Solve: 1. [X10SLM-F/X10SLL-F] Output 50@ dutycycle when bmc reboots 2. [X10SLM-F/X10SLL-F] Change sensor name to "3.3V AUX" 3. [X10SLL-SF] BMC can't boot successfully 4. #45619 It not work if run "ChnageBIOScfg" and "Loaddefault" of OOB functions 5. [X10DRI_F] Add sensor supports 6. Preserve the whole 64k block where SMIBIOS data resides. [Validation Steps] a. Go to the bios update page b. Update bios image only with preserving SMBIOS. ===================================================================================== Filename: SMT_X10_104.bin version: 1.04 Date: 05-10-2013 SVN: 388 U-Boot build time : May 9 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r18 Solve: 1. Output 100@ dutycycle for X10SLM-F/X10SLL-F. 2. Update the thermal curve for heavy IO fan mode. [45018] Sometimes Auto-Resize Window Does Not Work When Booting into OS [45209] IPMI KVM window doesn't have Power Control option Support high resolution up to 1920*1200. [45463,45401,45381,45347] BMC incorrect reponse detected during eburn test ===================================================================================== Filename: SMT_X10_103.bin version: 1.03 Date: 05-03-2013 SVN: 376 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: Add OOB event log. OOB file build date mis-match (Sensor type : 0xCA, Event Data 1) OOB feature initial failure (Sensor type : 0xCA, Event Data 2) [X10SL7-F] 45347 BMC incorrect reponse detected during eburn test [X10SLE-F/X10SLD-F] 45381 BMC incorrect reponse detected during eburn test ====================================================================================== Filename: SMT_X10_102.bin version: 1.02 Date: 04-26-2013 SVN: 367 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: [X10SLM-F/X10SLL-F] 45067 part of the Eburn stress test is fail (ipmi_si: Error clearing flags: cc) [X10SLM+-LN4F/X10SLH-F/X10SL7-F/X10SLA-F] 45231 Please Change Bios String in IPMI Web System Information Page to BIOS [X10SLE-F/X10SLD-F] 45096 SSM Power Supply status is abnormal ====================================================================================== Filename: SMT_X10_101.bin version: 1.01 Date: 04-19-2013 SVN: 352 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: Support Heavy IO fan control mode Solve IPMI login web page is gone on ie8 & ie9 [X10SLM-F/X10SLL-F] 45044 IPMI SOL can't working. 45040 X10SLM-F->please add heavy I/O mode at FAN speed control mode 44962 IPMI Web GUI is gone with IE broswer Set smi pin as input low to aviod bios hang at 9A when system is powered on [X10SLM+-LN4F/X10SLH-F/X10SL7-F/X10SLA-F] 45022 IPMI Web Not Working Correctly With Microsoft Internet Explorer 44869 Email Alert Shows X10_XLH for X10SLH-F [X10SLE-F/X10SLD-F/X10SL7-F] Set up GPIOR3 for PHY Reset pin on rev 1.01 [X10SLE-F/X10SLE-F] Optimize the power consumption for these 2 motherboards When the system is off, lower the speed of dedicated LAN to 10M. When the system power up, the speed will come back to the original speed. ====================================================================================== Filename: SMT_X10_100.bin version: 1.00 Date: 04-11-2013 SVN: 336 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 For beta release ====================================================================================== Filename: SMT_X10_032.bin version: 0.32 Date: 04-10-2013 SVN: 335 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: Support power source page and power monitor page on IPMI web-gui Support set system mac address command (need bios support and clear browser cache after updating ) [X10SLM-F] Use ME to read CPU temp instead of peci (Please re-work HW) [X10SLM-F/X10SLL-F] 44361 Chassis intrusion doesn't work [X10SLM+-LN4F/X10SLH-F/X10SL7-F/X10SLA-F] 44869 Email Alert Shows X10_XLH for X10SLH-F MB 44854 All Fans Do Not Stay at Full Speed During Fan Failure 44833 CPU Overheat Deassertion Thresholds Do Not Follow Thermal Guideline ====================================================================================== Filename: SMT_X10_031.bin version: 0.31 Date: 04-03-2013 SVN: 329 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: Please use factory reset after downloading new firmware [X10SLM-F] 44312 IPMI IKVM Reset function is not working [X10SLM+-LN4F/X10SLH-F/X10SL7-F/X10SLA-F] Add VRM sensor 44747 Shared LAN Not Working 44426 [NM] Cannot Read Entire Platform Statistics ====================================================================================== Filename: SMT_X10_030.bin version: 0.30 Date: 03-29-2013 SVN: 320 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: [X10SLM-F/X10SLL-F] 44672 BIOS IPMI Network Link Status is "No Connect" when IPMI connected 44322 IP Access Control function is not working 42897 IPMI Mouse default setting is incorrect [X10SL7-F] 44145 Cannot get any ME information via SMCIPMITool [X10SLM-LN4F/X10SLH-F] 44479 IPMI Network Link Status Shows "No Connect" 44402 Cannot Flash BIOS via OOB [X10SLA-F] 44369 CPU Temp. and Memory Temp. status is "N/A ====================================================================================== Filename: SMT_X10_029.bin version: 0.29 Date: 03-25-2013 SVN: 313 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: Please use progrmmer to flash the firmware [X10SLM-F] Add board support ====================================================================================== Filename: SMT_X10_028.bin version: 0.28 Date: 03-21-2013 SVN: 309 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: 1. Fix the issue smcipmitool can't upgrade the firmware.(smcipmitool verion MUST be 2.4.11 and later) Usage: smcipmitool ADMIN ADMIN ipmi flasha 2. Fix the issue SMCIBU will show the error message "product key not active" when flash BIOS on X10SSL-F. [X10SLE-F] [X10SLM-F] 44312 IPMI IKVM Reset function is not working 41936 Fan Pulse-Width-Modulation Measurement fail [X10SLL-F] 44382 How do I change the serial output from SOL to COM2 (header) 44136 No PCH temperature in IPMI sensor readings ====================================================================================== Filename: SMT_X10_027.bin version: 0.27 Date: 03-15-2013 SVN: 298 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 **** After updating this firmware, please do factory reset in the maintainance page **** Solve: Fix the issue upgrading FW without preserving [validation step] 1.First burning the 00.27 firmware and then do factory reset in maintainance page 2.Upload the 00.26 firmware and uncheck the preserved box in firmware upload page 3.After burning process is finished, you can see the sensor positions are changed in sensor page (In 0026, we swap the sensor orders ) 4.If you upgrade from 00.26 to 00.27 by above procedure. Then you will not see the sensors are swapped [X10SLE-F] 44446 "-12V" should be removed from IPMI sensor reading 44384 PCH Temperature Missing 44383 CPU Temperature Missing [X10SLM-LN4F/X10SLH-F] 44421 CPU and PCH Temperature Missing With IPMI FW v0.26 44140 CPU Overheat LED [X10SLM-F] 44392 Missing/bogus sensors from ipmitool 44391 Missing VCORE and VDIMM in IPMI sensor 44344 IPMI Watchdog NMI function is not working 44322 IP Access Control function is not working 44279 IPMI sometimes will generate Chassis Intrusion and -12V event in Event log [X10SLL-F] 44381 Intrusion reset from IPMI will generate weird SEL 44358 IPMITOOL sdr command has some extra sensor readings compared to web-gui 44325 SEL has some voltage logs after running BMC reset test 44136 No PCH temperature in IPMI sensor readings [X10SLA-F] 44369 CPU Temp. and Memory Temp. status is "N/A" in IPMI Monitor sensor 44152 The FAN pluse test fail [X10SL7-F] 44353 [RE-OPEN] - Sensor readings incorrect after system wakes up from S3 ====================================================================================== Filename: SMT_X10_026.bin version: 0.26 Date: 03-08-2013 SVN: 284 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: X10SLE-F [44098] Virtual Media: CD-ROM Image ISO Mount Shows Mounted as USB Floppy&Flash X10SLL-F [44210] There won't be any sensor readings sometimes - via web or KCS interface New feature: Flash dos tool (Must use this version and above.) ====================================================================================== Filename: SMT_X10_025.bin version: 0.25 Date: 03-04-2013 SVN: 274 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: X10SLA-F [44152] The FAN pluse test fail [44035] Memory events log test fail X10SLH-F/ X10SLM-LN4F [44140] CPU Overheat LED [42624] DIMM Temperature Sensor Showing N/A X10SLE-F [44097] System Takes Long Time to Boot [44094] No DIMM Temperature Seen on IPMI Web Sensor Readings X10SLD-F [44066] no hardware monitor in ipmi X10SL7-F [44056] IPMI initializes every time I reboot or turn on the system ====================================================================================== Filename: SMT_X10_024.bin version: 0.24 Date: 02-23-2013 SVN: 252 U-Boot build time : Feb 22 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: X10SLH-F/X10XLM-LN4F [43961] Remote Console Preview Takes Longer to Refresh than Previous X9 Generation X10SLL-F/X10XLM-F [43893] Chassis Intrusion always is fail and didn't reset [43891] IPMI Event Log has some undefined message when system boot-up or OS reboot [43154] Watchdog function is not working X10SL7-F [43878] After system wakes up from S3 and boots into OS there are not IPMI sensor readings [43329] IPMI LED is not blinking anymore after consective cold reset X10SLE-F [43869] Unable to establish LAN session" after running IPMI Cold Reset for 2529 times through onboard LAN1 X10SLD-F Add board support ====================================================================================== Filename: SMT_X10_023.bin version: 0.23 Date: 02-01-2013 SVN: 234 U-Boot build time : Jan 31 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Please clean web page before login the IPMI web page Solve: [X10SLH-F/X10SLE-F] Failed to set static IPMI LAN IP address in BIOS [X10SL7-F] Web-session times out after 15 mins Add the web session page and web session timeout value on web page (1-30 minutes) Sensor readings appear on IPMI web-gui before all the option ROM have been initialized Sometimes After Shutdown From OS and then Power On, Random Sensors Will Disappear IPMI restart occasionally after push reset button Add AC Power On Event Log on web page Ipmi command, 0x30 0x70 0x64 Data1 Get/Set ->[0/1] Data2 set ac power on event flag -> [0/1] //disable / enable ====================================================================================== Filename: SMT_X10_022.bin version: 0.22 Date: 02-01-2013 SVN: 218 U-Boot build time : Jan 31 2013 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: [X10SL7-F/X10SLM-LN4F]IPMI KVM: No IKVM signal when resolution is set to 1024x768x8 mode [X10SL7-F] PCH temperature is shown as 4 degrees (Intel bug, work around solution) [X10SLL-F] Workaround solution to fix the power button can't work properly. [X10SLE-F] Support HDD sensor Solve the language hang problem in ikvm viewer Solve the SDR could not be updated [Denis] ====================================================================================== Filename: SMT_X10_021.bin version: 0.21 Date: 01-30-2013 U-Boot build time : 12-19 2012 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: [X10SLL-F/X10SLL-F] For CM release set GPIOE5 as input pin after setting to output pin state to avoid power button fail solution ====================================================================================== Filename: SMT_X10_020.bin version: 0.20 Date: 01-29-2013 SVN: 203 U-Boot build time : 12-19 2012 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Solve: [X10SLL-F/X10SLL-F] For CM release set GPIOE5 output high at boot code stage to avoid i210 crash down set GPIOC1 input, GPIOE2 output set GPIOE3 output ====================================================================================== Filename: SMT_X10_019.bin version: 0.19 Date: 01-25-2013 SVN: 201 U-Boot build time : 12-19 2012 Java SOL Viewer version : v0.5.9 Java iKVM Viwer version : v1.69 r13 Please use programmer to burn this firmware Please clear Java cache (SOL verion is updated) Solve: [X10SLM-LN4F] Unreliable IPMI connection on shared LAN [X10SL7-F] SOL Can Open Multiple Windows [X10SLE-F] Add sensor list (HDD sensor is not ready) ====================================================================================== Filename: SMT_X10_018.bin version: 0.18 Date: 01-18-2013 SVN: 187 U-Boot build time : 12-19 2012 Java SOL Viewer version : v0.5.8 Java iKVM Viwer version : v1.69 r13 Please uncheck the Preserve Configuration box to restore the factory default setting of BMC Solve: [X10XL7-F] Fix vcore senor value is not right Systerm Temperature (RT1) Event Cannot Be Logged No IPMI Log for PCH Overheat Hardware; IPMI [X10SLM-LN4F] KVM window closes itself [X10SLL-F] The FAN speed control curves for CPU can't follow thermal design guide [X10SLE-F] Add board support ====================================================================================== Filename: SMT_X10_017.bin version: 0.17 Date: 01-11-2013 SVN: 175 Solve Preview function is working ( Remember it takes about 6 seconds to refresh the screenshot in X10, and 1280 x 1024 resolution maximum ) Device 3 function works at virtual storge Solve when switching to share LAN, can't get IP and network message is not correct on network page Solve peripheral Temperature overheat asserted event is not log in SEL. Solve BMC will has kernel panic after several times change on Lan Interface setting in Network configuration. [X10SLM_LN4F/X10SLH-F/X10SL7-F] Correct vcore voltage on web page No overheat beep alarm (controlled by NCT6776) Correct system temp disappeared in sensor reading page Correct sensors will disappear in sensor reading page [X10SLL-F/X10SLM-F] Add watchdog function Add Beep function (controlled by AST2400 PWM) ====================================================================================== Filename: SMT_X10_016.bin version: 0.16 Date: 01-07-2013 SVN: 152 Solve [X10SL7-F/X10SLA-F] Add board support [X10SLM_LN4F/X10SLH-F/X10SL7-F] Correct vcore voltage on web page [X10SLL-F/X10SLM-F] Correct -12v sensor voltage on web page Add watchdog function Known issues 1. Preview has some problems ====================================================================================== Filename: SMT_X10_015.bin version: 0.15 Date: 12-28-2012 SVN: 134 Solve Fan control function is ok [X10SLH-F/SLM_LN4F] Chassis Intrusion Shows Wrong Time Stamp in Event Log [X10SLH-F/SLM_LN4F] Fine tune the parameters of superio NCT6776 based on sensor list [X10SLL-F/X10SLM-F] -12v sensor reading fails Known issues 1. Preview has some problems ====================================================================================== Filename: SMT_X10_014.bin version: 0.14 Date: 12-21-2012 SVN: 116 Solve Virtual media funciton is working Preview function is working It show wrong share/dedicate information on network config web page Add GUID for ATENX10 BMC is C 0 0 1 M S Set default Mac address of Bootloader is 00:00:00:00:00:00 [X10SLL-F/X10SLM-F] Voltage sensor has been fined tune Power fail led and led works correctly [X10SLH-F/X10SLM-LN4F] Fan Fail Event Log for FAN1 and FAN2 Missing Lower Non-Critical Status Factory Default Will Cause BMC to Lose MAC Address [X10SL7] support Known issues 1. Fan fail and pwm has some problems. 2. [X10SLL-F/X10SLM-F] Front & Rear temperature sensors, smbus may be failed after long time testing ====================================================================================== Filename: SMT_X10_013.bin version: 0.13 Date: 12-13-2012 SVN: 95 Solve Important !! <=Please use programmer to burn this firmware if previous firmware is older then fw.012 verion 1. Add board id BOARD_X10_SLM_LN4 0x806 2.[X10SLM-LN4] 1.Change Vcore threshold, M,B,K2,K1. 2.Change ˇ§CPU VTTˇ¨ to ˇ§-12Vˇ¨ and Adjust this threshold, M, B, K2, K1 3. [X10SLM] 1.Add all sensors [except chassis intrusion] Known issues 1. It can only mount virtual media at the 1st time, and umount/remount funciton failed 2. Preview is not working ====================================================================================== Filename: SMT_X10_012.bin version: 0.12 Date: 12-07-2012 SVN: 73 Solve 1. Enable COM1 & COM2 at bootloader Important !! <=Please use programmer to burn this firmware 2. Network function works 3. [X10SLL-F/X10SLM-F] sensors wroks (except CPU peci temp, overheat function) 4. UID funciton works 5. SOL function works 6 Post snoppy function works on IPMI web page 7. [X10SLH-F/X10SLM-LN4F] sensors wroks [except CPU peci temp, overheat function] Known issues 1. Virtual media is not working 2. Remote control is not working 3. [X10SLL-F/X10SLM-F] fan speed is full speed now ====================================================================================== Filename: SMT_X10_011.bin version: 0.11 Date: 11-30-2012 SVN: 49 This bin code is for all X10 boards. Solve 1. Remote function ok 2. KCS works. bios please use KCS4 & KCS5; ipmicfg and other utilities will use KCS2 & KCS3 3. Add board id Known issues 1. Network driver has bugs. The failover mode fails, and dynamic plugging in/pulling out the network may fail. After setting the bmc address, you may have to ac power off and power on again, and the network works. 2. Sensors are working except memory temperature detection. 3. SOL is not working 7. Virtual media is not working 8. Sensor without SIO (only completed 6776 SIO sensor) ====================================================================================== Filename: SMT_X10_010.bin version: 0.10 Date: 11-26-2012 SVN: 33 This bin code is for all X10 boards. Known issues 1. Network driver has bugs. The failover mode fails, and dynamic plugging in/pulling out the network may fail. After setting the bmc address, you may have to ac power off and power on again, and the network works. 2. Sensors are working except memory temperature detection. 3. In SOL, only one way is passed 4. remote control is not working 5. In KCS, only CA2 & CA3 works. Currently, bios & bmc cannot talk to each other. 6. Ipmicfg works. 7. Virtual media is not working 8. Sensor without SIO (only completed 6776 SIO sensor) ======================================================================================